Publicidad
Idiomas disponibles
Idiomas disponibles
3.1. DEVICE DESCRIPTION
WIE-PM-2500
1
2
8
3
7
4
6
5
WIE-PM-3000
1
2
8
3
7
6
4
5
1.
Charging hopper
2.
Tractor hitch holder
3.
PTO drive shaft
4.
Hole for tractor hitch
5.
Frame
6.
Gearbox
7.
Chute
8.
Top casing
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 10 cm distance
between each side of the device and the wall or other
objects. The device should always be used when positioned
on an even, stable, clean, fireproof and dry surface, and
be out of the reach of children and persons with limited
mental and sensory functions.
EN
ASSEMBLING THE DEVICE
After unpacking the device, perform the following steps:
•
Install the grid in the hopper, then put the hopper on
the machine housing and screw it on.
•
Screw the chute to the machine.
•
screw one end of the drive shaft to the machine as
shown in the figure below.
CONNECTING THE MACHINE TO THE TRACTOR
•
Insert the hitches in the holes (4) as shown in the
figure below.
•
Use the hitches and the holder (2) to attach the
machine.
•
Connect the other end of the drive shaft to the
tractor.
12
3.3. DEVICE USE
1.
Before starting the machine:
•
check that all bolts and screws are tightened.
•
lubricate the bearings as per the instructions in 3.4.
•
set the roller pressure as per the instructions in 3.4.
•
when using a new die for the first time, grind it as per
the instructions in 3.4.
2.
Start the tractor with the machine drive shaft
attached. The die will start to rotate.
3.
Place the granulate container under the chute.
4.
Pour the mix into the hopper. Increase the amount of
poured material gradually to avoid clogging the die
or overloading the machine. Pouring in too much at
once may cause the die to clog.
Caution:
•
if the material is too dry, it will not be pressed
properly;
•
if the material is too moist, the pellets will be of poor
quality;
•
the maximum length of the material particles should
be approx. 5 mm. Longer material may clog the
machine and reduce its efficiency. Too large material
should be broken / cut into smaller particles.
5.
After a short time, pellets will be falling into the
container under the chute. They will achieve their
final hardness and consistency only after cooling.
6.
Proceed until the mix is completely processed.
7.
After finishing work, turn off the machine by stopping
the tractor.
NOTE: Do not stop the machine while making pellets
(except for an emergency stop), otherwise it will get
clogged.
Clean the machine so that pellet residues do not
remain on the rolls and in the dia.
3.4. CLEANING AND MAINTENANCE
Before
each
cleaning,
adjustment,
replacement
attachments, and also when the machine is not in use, stop
the drive by turning off the tractor. Then disconnect the
drive shaft from the tractor to avoid accidental starting.
a)
Use only non-corrosive cleaners to clean the surface.
b)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
c)
Do not spray the device with a water jet or submerge
it in water.
d)
Do not allow water to get inside the device through
vents in the housing of the device.
e)
Clean the vents with a brush and compressed air.
f)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
g)
Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
h)
Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils or
other chemical substances because it may damage
the device.
i)
Regularly lubricate the machine as per the
instructions.
EN
GRINDING A NEW DIE
Before first use, a new die should be polished and cleaned
using the following process:
a)
Prepare
•
5kg flour or saw dust,
•
5 kg of fine sand (optional),
•
1,5 l of vegetable, used or dirty oil
b)
Mix all ingredients in a bucket until to prepare a
mixture like in the photo below.
c)
Press the mixture 80 to 90 times through the die,
until the granules coming out of the chute meet the
quality requirements.
of
13
Publicidad
