Publicidad
GENERAL NOTES
The instructions included in the attached installation
manual must be followed carefully when installing a
ffuuss
eos hand dryer.
TM
ffuuss
TM
will not be liable for any damage to property
or personal injury or death resulting from non-
compliance with the instructions contained herein
and in the installation manual.
Make sure your ffuuss
eos hand dryer works
TM
properly before allowing the public to use it.
Do not use the ffuuss
eos hand dryer for any
TM
purpose other than drying hands.
Using authentic ffuuss
TM
spare parts can extend the
correct and safe functioning of your unit.
WARNING:
In order to create a safe environment for
visually impaired customers, fixtures must be
detectable with a cane. The diagram highlights this
requirement.
ADA guidelines state that fixtures above 27" (685
mm) must not protrude from the wall more than 4"
(100 mm). A low fixture such as a waste receptacle
can satisfy this requirement if it is detectable
below the protruding fixture (usually hand dryers
or towel dispensers).
Keep in mind that it's always important to double
check the requirements with local laws, as these
supersede Federal requirements.
NOTE: ffuuss
TM
reserves the right to make changes without prior notice.
HOW TO USE
Place your hands in the drying area of the ffuuss
hand dryer to activate the operation and the air
outlet. Leave your hands in the drying area until the
end of the cycle.
CLEANING THE DEVICE.
Surfaces.
Only clean the surfaces of the ffuuss
TM
eos hand
dryer with a damp cloth. Do not use abrasive or
caustic products.
4" max
100 mm
MAINTENANCE ADVISE
Air intake.
TM
Regularly check the air intake at the base of the
ffuuss
hand dryer and make sure it is free of
TM
dust, rubbish and other particles, if not, proceed to
clean it to free all the holes of possible dirt. If the
ffuuss
TM
hand dryer has a HEPA filter H13, change it
when necessary or at least once a year. Also, make
sure that all surfaces of the ffuuss
TM
are properly cleaned to maintain uninterrupted
operation.
TROUBLESHOOTING.
Important: turn off the electrical supply to the ffuuss
Problem
Action
ffuuss
The
TM
hand dryer does not
Make sure the
start.
the wiring are properly connected. If not
properly connected, contact the installer.
ffuuss
Check that there are no obstructions or
The
TM
hand dryer starts and
turns off erroneously.
barriers in the drying cavity. If there are,
withdraw them.
ffuuss
TM
Proceed to reinitiate the dryer
Sometimes the
hand dryer
turns off when it is in use and then
disconnecting it from the electrical
supply. Once it is plugged in again, wait for
starts again after a while.
6 minutes before using it.
The
ffuuss
TM
hand dryer continues
A 2 second delay after hands have been
to function after hands have been
removed is acceptable.
removed.
The
ffuuss
TM
hand dryer is not
Verify and clean any obstructions in
the inlet and monitor the state of the
drying hands properly.
HEPA filter. Follow the maintenance
recommendations
ffuuss
The
TM
hand dryer works only
Check that there are no objects or
barriers in the drying cavity. If there are
for a couple of seconds and then it
turns off.
withdraw them.
TEST
Make sure that the ffuuss
connected to the electrical supply. Once plugged
in wait for 6 minutes. Put your hands in the
drying area to start the air flow in the ffuuss
eos hand dryer. Withdraw hands, and the unit will
automatically stop.
hand dryer
TM
before servicing it.
If the problems persist
ffuuss
TM
hand dryer and
Contact your
distributor, or use
the contact email
technical@ffuuss.com,
or the telephone
+34 910 128 093
TM
eos hand dryer is
TM
Publicidad
