VONROC CT503DC Traducción Del Manual Original página 7

temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY INSTRUCTIONS
a) This power tool is intended to function as a grind-
er, sander, wire brush, polisher, carving or cut-off
tool. Read all safety warnings, instructions,
illustrations and specifi cations provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fi re and/or
serious injury.
c) Do not use accessories which are not specifi -
cally designed and recommended by the tool
manufacturer. Just because the accessory
can be attached to your power tool, it does not
assure safe operation.
d) The rated speed of the grinding accessories must
be at least equal to the maximum speed marked on
the power tool. Grinding accessories running faster
than their rated speed can break and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately controlled.
f) The arbour size of wheels, sanding drums or any
other accessory must properly fi t the spindle or
collet of the power tool. Accessories that do not
match the mounting hardware of the power tool
will run out of balance, vibrate excessively and
can lead to loss of control of the power tool.
g) Mandrel mounted wheels, sanding drums, cut-
ters or other accessories must be fully inserted
into the collet or chuck. If the mandrel is insuf-
fi ciently held and/or the overhang of the wheel
is too long, the mounted wheel may become
loose and be ejected at high velocity.
h) Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, sanding drum for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory
WWW.VONROC.COM
is dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged acces-
sories will normally break apart during this test
time.
i) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable
of stopping fl ying debris generated by various
operations. The dust mask or respirator must be
capable of fi ltrating particles generated by your
operation. Prolonged exposure to high intensity
noise may cause hearing loss.
j) Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of work piece or of a broken accessory may fl y
away and cause injury beyond immediate area of
operation.
k) Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
l) Always hold the tool fi rmly in your hand(s)
during the start-up. The reaction torque of the
motor, as it accelerates to full speed, can cause
the tool to twist.
m) Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in
use. Clamping a small workpiece allows you
to use your hand(s) to control the tool. Round
material such as dowel rods, pipes or tubing
have a tendency to roll while being cut, and may
cause the bit to bind or jump toward you.
n) Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled
into the spinning accessory.
o) Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the
power tool out of your control.
EN
7