VONROC CT503DC Traducción Del Manual Original página 9

carefully re-enter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
g) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick-
back. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
h) Use extra caution when making a "pocket cut"
into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kick-
back.
ADDITIONAL SAFETY INSTRUCTIONS FOR
WIRE BRUSHING OPERATIONS
Safety warnings specifi c for wire brushing operations:
a) Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush. The wire bristles can easily pene-
trate light clothing and/or skin.
b) Allow brushes to run at operating speed for at
least one minute before using them. During
this time no one is to stand in front or in line
with the brush. Loose bristles or wires will be
discharged during the run-in time.
c) Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire
fragments may be discharged at high velocity
during the use of these brushes and may be-
come imbedded in your skin.
FOR THE CHARGER
Intended use
Charge only rechargeable battery packs. Other
types of batteries may burst causing personal
injury and damage.
a) The appliance is not to be used by persons (in-
cluding children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given super-
vision or instruction
b) Children being supervised not to play with the
appliance
c) Do not recharging non-rechargeable batteries!
d) During charging, batteries must be placed in the
well ventilated area!
e) Integrated batteries may only be removed for
disposal by qualifi ed personnel. Opening the
housing shell can destroy the power tool.
WWW.VONROC.COM
To remove the battery from the power tool, press
the On/Off switch (5) until the battery is fully dis-
charged. Unscrew the screws on the housing and
remove the housing shell in order to remove the
battery. To prevent a short circuit, disconnect the
connectors on the battery one at a time and then
isolate the poles. Even when fully discharged,
the battery still contains a residual capacity,
which can be released in case of a short circuit.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fi re, electric shock and personal
injury. Read the following safety instructions.
Always check that the power supply
corresponds to the voltage on the rating plate.
Your machine is double insulated, therefore
no earthwire is required.
2. MACHINE INFORMATION
Intended use
This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
This combitool is great for editing of materials like
wood, plastic, stone, shell aluminium, brass and steel.
Always use the proper accessories and speed setting.
TECHNICAL SPECIFICATIONS
Model No.
Rechargeable Battery
Battery charging time
Maximum disc diameter
Maximum drill diameter
No load speed
Capacity of spring chuck
Weight
Lpa (Sound pressure level)
Lwa (Sound power level)
Vibration
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardised test given in EN 60745; it may
EN
CT503DC
4V Li-ion 600mAh
2 hours
Ø35 mm
Ø2.3 mm
5000/10000/15000/min
2.3 mm
0.1 kg
79+3 dB(A)
90+3 dB(A)
1.177+1.5 m/s 2
9