Makita HR007G Manual De Instrucciones página 18

Grease
Optional accessory
Coat the shank end of the drill bit beforehand with a
small amount of grease (about 0.5 - 1 g).
This chuck lubrication assures smooth action and lon-
ger service life.
Installing and removing drill bit
Clean the shank end of the drill bit and apply grease
before installing the drill bit.
► Fig.15: 1. Shank end 2. Grease
Place the shank end of the drill bit into the chuck, and insert it
further into the chuck while hand-turning the drill bit so the shank
end well fits into the chuck slot and becomes fully engaged.
Having installed the drill bit, try pulling it back to ensure
it is securely held in place.
► Fig.16: 1. Drill bit 2. Chuck
To remove the drill bit, push the chuck cover down all
the way and pull the drill bit out.
► Fig.17: 1. Drill bit 2. Chuck cover
Chisel angle (when chipping,
scaling or demolishing)
The chisel can be secured at the desired angle. Switch
the action mode changing knob to the O symbol, and
then turn the chisel to your desired angle.
► Fig.18: 1. Action mode changing knob 2. O symbol
Switch the action mode changing knob to the
hand-turning the chisel to ensure it is securely held in place.
Depth gauge
The depth gauge is convenient for drilling holes of uniform depth.
Press and hold the lock button, and then insert the depth
gauge into the hex hole. Make sure that the toothed side of
the depth gauge faces the toothed marking on the hex hole.
► Fig.19: 1. Depth gauge 2. Lock button 3. Hex hole
4. Toothed side 5. Toothed marking
Adjust the depth gauge by moving it back and forth
while pressing the lock button. After the adjustment,
release the lock button to lock the depth gauge.
NOTE: Make sure that the depth gauge does not
touch the main body of the tool when attaching it.
Dust collection system
Optional accessory
Installation
1. Slide the air duct cap out of the motor housing
while lifting the lock tab up to the unlocked position.
► Fig.20: 1. Air duct cap 2. Lock tab
2. Mount the tool onto the dust collection system by
sliding the guide grooves on bottom surface of the gear
housing over the guide rails on top surface of the dust
collection system until it locks in place with a click.
► Fig.21: 1. Guide grooves 2. Guide rails 3. Dust
collection system
Uninstallation
1. Dismount the tool from the dust collection system
by sliding the tool away off while pressing the lock off
button on the dust collection system.
► Fig.22: 1. Dust collection system 2. Lock off button
2.
Slide the air duct cap back along the guide
grooves on gear housing until it locks in place with a
click.
► Fig.23: 1. Air duct cap 2. Guide grooves
NOTICE:
back over the air duct after detaching the dust
collection system from the tool. Tool performance
can be affected if it is operated without the air duct
cap in place.
Adjusting nozzle position
Slide in and out the nozzle guide while pressing the
guide adjustment button, and then release the button
at an exact position where the tip of the drill bit sits just
behind the front surface of the nozzle.
► Fig.24: 1. Nozzle guide 2. Guide adjustment button
NOTE: Before adjusting the nozzle position, press
the guide adjustment button to release the tension on
the nozzle guide and set it free into a fully extended
position.
Adjusting drilling depths
Drilling depth can be adjusted by changing the lengths
symbol. Try
between the depth adjustment button and rear end of
the nozzle guide. Press and hold the depth adjustment
button and slide it to your desired position.
► Fig.25: 1. Depth adjustment button 2. Nozzle guide
Storage
NOTICE:
time, the nozzle guide needs to be extended to
approximately 100 mm from its fully shortened
position. Failing to do so may damage the duct hose
pre-installed in the nozzle guide.
► Fig.26: 1. Guide adjustment button 2. Approx.
Dust cup
Optional accessory
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Model
Dust cup 5
Dust cup 9
► Fig.27: 1. Dust cup
18 ENGLISH
Make sure to place the air duct cap
3. Tip of drill bit 4. Front surface of nozzle
3. Drilling depths
When not in use for a certain period of
100 mm
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm