Kreg ACS-SAW Manual Del Propietário página 25

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1. Burning material
a. Check sharpness of the blade. Replace if necessary.
b. Check the blade for pitch build-up. Clean with commercially
available blade cleaner.
c. Check Toe in. (See Toe in adjustment.)
2. Splintering on the off-cut
a. Verify the splinter guard contacts the workpiece.
b. Verify there is not a gap between the inside edge of the
splinter guard and the blade teeth. If the splinter guard was
not tightened before use or loosened during use, it may have
been damaged. Replace the splinter guard.
3. Splintering on the workpiece (material under the track)
a. Verify the front edge of the blade is flush with the anti-chip
strip. If there is a gap between the blade and the anti-chip
strip, replace and trim the strip. (See Trim the anti-chip strip.)
4. Poor dust collection
a. Empty the dust bag after every second or third cut.
b. Occasionally blow out the dust bag fabric with compressed air.
Accumulated fine dust can clog the dust bag fabric pores.
c. Verify dust is not clogging the blade housing or dust port. Blow
out the housing and port with compressed air.
d. When making many cuts in one work session, connect the
saw to a shop vacuum.
5. Cuts slightly off 90°
a. Verify the bevel overrides are not engaged.
b. Check the bevel calibration. (See Calibrate the bevel scale.)
6. Motor boggs down
a. Verify the speed-control dial is set to maximum speed
(setting 6).
b. Check the sharpness of blade. Replace if necessary.
c. Check the blade for pitch build-up. Clean with commercially
available blade cleaner.
d. Reduce feed rate (movement of saw along the track). Wet or
hard woods require a slower feed rate.
e. Blade kerf in the workpiece may be closing and pinching the
blade. Stop cutting, remove the saw from the workpiece, and
start the cut over to widen the saw kerf. If pinching persists,
discard workpiece.
TELL US ABOUT YOUR EXPERIENCE. YOUR OPINION COUNTS.
We're always working to improve Kreg
project-building experiences. You can help by sharing your feedback at www.kregtool.com/feedback.
It only takes a couple of minutes, and will help us to create products and support that serve your needs better.
PARLEZ-NOUS DE VOTRE EXPÉRIENCE. VOTRE OPINION EST IMPORTANTE POUR NOUS.
Nous cherchons toujours à améliorer les produits Kreg® et à nous assurer que vous soyez satisfait lorsque vous les utilisez pour effectuer vos projets de
construction afin de rendre votre expérience agréable. Vous pouvez nous aider en nous faisant part de vos commentaires au www.kregtool.com/feedback.
Cela ne prend que quelques minutes, et vos commentaires nous aideront à créer des produits et à fournir des services qui répondront mieux à vos besoins.
CUÉNTENOS SOBRE SU EXPERIENCIA. SU OPINIÓN CUENTA.
Siempre trabajamos para mejorar los productos Kreg
Puede ayudar compartiendo su retroalimentación en www.kregtool.com/feedback. Solo toma un par de minutos y nos estará ayudando a crear
productos y brindar un soporte que sirva mejor a sus necesidades.
TROUBLESHOOTING
7. Motor stops working after extended use
a. Inspect power cord for damage.
b. Switch damaged or worn. Call Kreg Customer Service for
c. Motor brushes worn. Call Kreg Customer Service for repair.
8. Wavy cut
a. Verify the tracking controllers are properly adjusted. They
should be tight enough to eliminate play between the saw and
guide track without hindering movement of the saw along the
b. Inspect the tracking controllers for damage. Call Kreg
c. Clean the anti-slip strips with a damp cloth and remove dust
from the workpiece. If the guide track slips sideways on a slick
optional track clamps, available from Kreg.
9. Saw will not plunge to desired depth
a. Check if mode is set to blade change mode
b. Make sure splinter guard has been properly trimmed
c. Make sure the chip strip on the guide track has been properly
10. Saw does not sit flat on the track
a. Check if mode is set to blade change mode
c. Loosen the snuggers and re-adjust
11. Saw does not glide down the track
a. Loosen the snuggers and re-adjust
c. Replace glide strips if necessary
12. Saw blade removal
13. Saw catches at beginning of cut
a. Check that the saw snuggers are on the track
b. Loosen snuggers and re-adjust
call Kreg Customer Service for assistance.
products and your satisfaction with them so that you have great
®
y su satisfacción con ellos para que tenga excelentes experiencias de construcción de proyectos.
®
repair.
track.
Customer Service for repair.
workpiece surface, secure the track to the workpiece with
trimmed
b. Clean track of any debris
b. Clean track of any debris
a. Blade bolt is reverse threaded, turn clockwise to loosen and
remove
ATTENTION
Should you encounter a problem not addressed above,

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Acs430Acs445Acs735Acs705

Tabla de contenido