Kreg ACS-SAW Manual Del Propietário página 4

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

filter out microscopic particles.
equipment, such as those dust masks that are specially designed to
• Avoid prolonged contact with dust from power sanding,
filter out microscopic particles.
dust to get into your mouth, eyes, or
sawing, grinding, drilling, and other construction activities.
• Avoid prolonged contact with dust from power sanding,
Terms and Definitions
Wear protective clothing and wash exposed areas with
sawing, grinding, drilling, and other construction activities.
The label on the saw may include the symbols below.
soap and water. Allowing dust to get into your mouth, eyes, or
Wear protective clothing and wash exposed areas with
or respirator should be worn by all
The symbols and their definitions are as follows:
lay on the skin may promote absorption of harmful chemicals.
soap and water. Allowing dust to get into your mouth, eyes, or
WARNING: A dust mask or respirator should be worn by all
lay on the skin may promote absorption of harmful chemicals.
persons entering the work area. The filter should be replaced daily or
WARNING: A dust mask or respirator should be worn by all
safety alert symbol
whenever the wearer has difficulty breathing. See your local hardware
persons entering the work area. The filter should be replaced daily or
volts
store for the proper NIOSH/OSHA approved dust mask.
V
whenever the wearer has difficulty breathing. See your local hardware
• The label on your tool may include the following symbols. The
store for the proper NIOSH/OSHA approved dust mask.
hertz
are as follows:
Hz
are as follows:
symbols and their definitions are as follows:
• The label on your tool may include the following symbols. The
amperes
A
A .......amperes
A .......amperes
V ......... volts
symbols and their definitions are as follows:
A .......amperes
watts
W
W ......watts
V ......... volts
Hz ....... hertz
W ......watts
direct current
W ......watts
Hz ....... hertz
min ..... minutes
.....alternating current
.....alternating current
alternating current
min ..... minutes
... direct current
.....alternating current
.....alternating or direct current
alternating or direct current
.....alternating or direct current
... direct current
....... Class I Construction
.....alternating or direct current
n o ......no load speed
Class I Construction (grounded)
n o ......no load speed
....... Class I Construction
...........
(grounded)
n o ......no load speed
Class II Tool (double insulated)
...........
(grounded)
....... Class II Construction
......earthing terminal
......earthing terminal
....... Class II Construction
earthing terminal
...........
(double insulated)
......earthing terminal
.....safety alert symbol
.....safety alert symbol
...........
(double insulated)
minutes
.../min per minute
min
A .......amperes
.....safety alert symbol
.../min per minute
BPM ..beats per minute
revolutions or reciprocations per minute
/min
BPM ..beats per minute
W ......watts
BPM ..beats per minute
beats per minute
BPM
.....alternating current
RPM ..revolutions per minute
RPM ..revolutions per minute
RPM ..revolutions per minute
revolutions per minute
RPM
.....alternating or direct current
n o ......no load speed
no load speed
......earthing terminal
Read the instructions
.....safety alert symbol
BPM ..beats per minute
Wear eye and ear protection
RPM ..revolutions per minute
Keep hands & body away from and to the side
of the blade. Contact with blade will result in
serious injury.
Blade change mode
Cut mode
GENERAL SAFETY GUIDELINES
Kreg
120V ~ 60 Hz 12A no = 2,000-6,000/min
Guidelines for extension cord use
Extension cords are only to be used for temporary purposes. They
do not replace the need for installation of outlets and proper wiring
where necessary.
In your work area:
1. Extension cords with an equipment grounding conductor
2. Extension cords must be protected from damage, and not
run through doorways or windows where the doors or
windows can close, causing damage to the cord.
3. Extension cords must be a minimum of 16 AWG and be
rated for the equipment in use.
4. Extension cords must be periodically inspected to ensure that
A .......amperes
5. Extension cords should not be run through water or allowed to
A .......amperes
W ......watts
W ......watts
.....alternating current
TABLE 1
Nameplate
.....alternating current
.....alternating or direct current
n o ......no load speed
.....alternating or direct current
n o ......no load speed
......earthing terminal
......earthing terminal
.....safety alert symbol
.....safety alert symbol
BPM ..beats per minute
NR – Not Recommended
BPM ..beats per minute
RPM ..revolutions per minute
RPM ..revolutions per minute
ACS-SAW
and other chemicals, which are known to the State of California to cause cancer and
reproductive harm. For more information go to www.P65Warnings.ca.gov.
you to wood dust, a substance known to the State of California to cause cancer. Avoid
inhaling wood dust or use a dust mask or other safeguards for personal protection.
For more information go to www.P65Warnings.ca.gov/wood.
ACS430
Carbon 1333-86-4, which are known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
KPS6512 plunge saw motor specifications
®
must be used at all times.
the insulation and conductivity of the wires are not compromised.
have connections that may be exposed to accumulated water.
Amperes
25'
50'
@120 V
Recommended Wire Gauge
0 -5
16
16
5.1 - 8
16
16
8.1 -12
14
14
12.1 - 16
12
12
WARNING:
This product can expose you to chemicals including Acrylonitrile
WARNING:
Drilling, sawing, sanding or machining wood products can expose
WARNING:
This product can expose you to chemicals including
Extension Cord Length
75'
100'
150'
16
14
12
14
12
10
12
10
NR
NR
NR
NR
200'
12
NR
NR
NR

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Acs430Acs445Acs735Acs705

Tabla de contenido