Publicidad
Idiomas disponibles
Idiomas disponibles
3.
Swing Stop
Top Trak
Knob
Stop Base
Lens
Stop Arm
Tape
Workpiece
Stop
Arm
ASSEMBLE THE STOP
DK1313
FT4257
FT4061
FT4137
FT4258
FT4257
FT4262
FT4212
Part#
Qty.
Description
FT4261
1
Swing Stop
FT4063
1
Lens
- Allows precise adjustment of Swing Stop
FT4061
1
Nyloc Nut
FT4137
2
Brass Washer
FT4064
1
Nylon Screw
DK1313 1
Black T-Knob
FT4060
1
Hex Head Bolt
FT4262
1
Stop Base
FT4212
1
T-Bolt
- Slides in T-Slot of aluminum trak
FT4257
4
Plastic Stop Bushing
FT4258
1
Plastic Support Button
*Please see step 4. Measuring Tape for setting the cursor correctly on your stops.
™
The Swing Stop™ measures and
records the distance between the end
of the board and the saw blade, drill bit
or router cutter. This allows you to easily
cut multiple pieces of stock to the exact
same length. Cutting numerous pieces
to the exact length without measuring is
easy. Gently press the end of the board
opposite the blade against the side
of the stop arm as shown at left. The
Swing Stop™ can be secured anywhere
along the track. The Swing Stop™ arm
can be assembled on either side of the
Stop Base knob although it must be
positioned between the Stop Base and
the saw blade.
The curved Swing Stop™ arm is
designed to rise automatically when a
board is pushed against the front of the
stop arm as shown at left. The Swing
Stop™ arm rests on top of the work
piece until the board underneath is
removed. When the board is removed
or moved to the side of the Swing Stop
the Stop arm drops down and is again
ready to be used as a stop.
FT4064
FT4137
FT4257
FT4261
Arm
™
- Position on side of stop base nearest blade
™
- Won't work loose during use
- Protects the Plastic Stop Bushing
- Used to calibrate lens zero position
- Tightens Swing Stop
assembly in position
™
- Secures Swing Stop
assembly
™
- Anchors assembly to aluminum trak
- Allows for smooth operation
- Allows for smooth operation
Precision Trak & Stop Instructions
4.
Locate the Measure Tape
Pencil
Mark
Square
™
24" Pencil
Marks
About the Lens
FT4060
FT4063
Red Line
Cursor
3/8" off-set
Set the Cursor
Measuring Tape
1. Cut a straight 3/4" thick piece of material
exactly 24" long by 3" wide.
Saw
Blade
24"
2. Turn the board on edge and place the
board with one end against the teeth of the
saw blade as shown at left.
3. Use a square or similar layout tool to
place a pencil mark across the top of the
fence onto the Top Trak on either side of the
indentation for the Self Adhesive Measuring
Tape. Butt the square against the reference
Pencil
Marks
board so that the pencil marks will be
exactly 24" from the blade as shown. If you
have placed Top Trak on both sides of the
blade repeat the same process for the other
side of the blade.
4. Align the 24-3/8" mark of the Self
Adhesive Measuring Tape to the pencil
mark and adhere
3/8"
the Tape to the indentation along the length
off-set
of the Top Trak. Cutoff excess tape with
scissors.
Note: Placing the Tape is much easier if
you slice the backing of the Measuring Tape
24"
under the 24" mark and fold over to expose
Board
only a short amount of the adhesive.
Both the Production Stop and the Swing
Stop™ feature an adjustable lens cursor
similar to the lens on a quality table saw rip
fence.
The lens is a clear material except for a red
line (cursor) on the bottom of the lens as
shown at left. The red line cursor makes it
easy to read the tape lines and fine-tune the
stop when compensating for blade thickness
variations or a tape that is not perfectly
positioned.
Note: When placing the self-adhesive tape
onto the track, the tape must be placed 3/8"
CLOSER TO THE SAW BLADE to allow the
Lens to function properly.
1. Adjust the cursor so it sits about 3/8" from the
edge of the stop. The cursor set screw is on
top of the stop arm.
2. Measure a piece of scrap wood. The exact
length of this scrap is not important. A board
about 24" works well because it gives you
plenty of room to make some test cuts.
3. Set the stop so the cursor reads a length less
than the length of the scrap piece.
4. Cut the scrap board to the new length and
measure the cut board.
5. Without moving the stop loosen the cursor set
screw and adjust it to read this exact
measurement.
Publicidad
