Publicidad
Idiomas disponibles
Idiomas disponibles
Pump Maintenance
This model does not require any pump maintenance.
The pump is pre-lubricated and sealed, requiring no
additional lubrication for the life of the pump.
ENGINE MAINTENANCE
WARNING
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
Disconnect the
spark plug
wire from the
spark
plug
and
place
the wire where it cannot contact
spark plug.
WHEN TESTING FOR ENGINE SPARK
Use
approved
spark
plug
tester.
DO NOT check for
spark with spark
plug
removed.
Oil
Oil Recommendations
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF, SG, SH, SJ or higher. DO NOT use
special additives.
1.
Choose a viscosity according to the following table:
;
L
L
J
[
2j0
00
20
:'2
2
60
80
/007
30
20
/0
0
l0
20
30
40
STARTING
TEMPERATURE
RANGE
ANTICIPATED
BEFORE
NEXT
OiL CHANGE
NOTE: Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol with "SJ/CF
ENERGY CONSERVING" or higher, is an acceptable
oil at all temperatures.
Use of synthetic oil does not
alter required oil change intervals.
* The use of multi-viscosity oils (5W-30, 10W-30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption. When using a multi-
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures below 40°F
(4°C), it will result in hard starting and possible engine
bore damage due to inadequate lubrication.
Checking Oil Level
Oil level should be checked prior to each use or at least
every 5 hours of operation. Keep oil level maintained.
1.
Make sure pressure washer is on a level surface.
2.
Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
and check oil level.
3.
Verify oil is at "Full" mark on dipstick. Replace and
tighten dipstick.
Adding Engine Oil
1.
2.
3.
,
@
Make sure pressure washer is on a level surface.
Check oil level as described in "Checking Oil Level".
If needed, slowly pour oil into oil fill opening to the
"Full" mark on dipstick. DO NOT overfill.
Replace and tighten dipstick.
Changing Engine Oil
Change engine oil after the first 5 hours and every
50 hours thereafter. If you are using your pressure
washer under extremely dirty or dusty conditions, or in
extremely hot weather, change oil more often.
CAUTION
Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
Thoroughly wash exposed areas with soap and water.
KEEP OUT OF REACH
OF CHILDREN.
DON'T
POLLUTE.
CONSERVE
RESOURCES.
RETURN
USED
OIL TO
COLLECTION
CENTERS.
Change oil while engine is still warm from running, as
follows:
1.
Drain fuel tank by running pressure washer until
fuel tank is empty.
2.
Disconnect spark plug wire and keep it away from
spark plug.
3.
Clean area around oil fill, remove oil fill
cap/dipstick. Wipe dipstick clean.
4.
Tip your pressure washer to drain oil from oil fill
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5.
Slowly pour recommended
oil (about 20 oz.) into
oil fill opening. Pause to permit oil to settle. Fill to
"Full" mark on dipstick.
6.
Wipe dipstick clean each time oil level is checked.
DO NOT overfill.
7.
Replace and tighten dipstick.
8.
Wipe up any remaining oil.
9.
Reconnect spark plug wire to spark plug.
17
Publicidad
