Publicidad
Idiomas disponibles
Idiomas disponibles
When the device is operating do not put hands into its openings
13.
Disconnect the charger before repairs.
14.
Protection class 2.
15.
The charger is designed to operate indoors in dry environment.
16.
Do not throw cells into fire.
17.
Maximum permissible cell temperature.
18.
Recycling
19.
CONSTRUCTION AND USE
Cordless blower is a hand held device. Drive consists of a DC
commutator motor. The cordless blower is a device designed for clean
up works around house and in home harden. It is perfect for cleaning
and removal of leaves, grass after mowing, needles of coniferous trees
that fall on terraces, pavements and paths. The device is not designed
for industrial applications, it can be used outdoors.
Use the tool only in accordance with its purpose.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Nozzle
1.
Nozzle lock button
2.
Switch
3.
Battery
4.
Battery lock button
5.
Charger
6.
LED diodes
7.
Button for battery level indication
8.
Battery level indicator (LED)
9.
* Differences may appear between the product and drawing.
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY / SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Nozzle - 1 pce
1.
PREPARATION FOR OPERATION
REMOVING AND INSERTING THE BATTERY
• Push the battery lock button (5) and slide out the battery (4) (fig. A).
• Insert charged battery (4) into the handle holder, you should hear when
the battery lock button (5) snaps.
BATTERY CHARGING
The battery for the device is supplied partially charged. Charge the
battery in ambient temperature between 4°C and 40°C. New battery, or
one that has not been used for a long time, will reach full efficiency after
approximately 3 to 5 charge/discharge cycles.
• Remove the battery (4) from the device (fig. A).
• Connect the charger (6) to a mains socket (230 V AC).
• Slide the battery (4) into the charger (6) (fig. B). Make sure the battery
is properly fitted (pushed to the end).
When the charger is connected to a mains socket (230 V AC), the green
diode (7) on the charger turns on to indicate connected supply.
When the battery (4) is placed in the charger (6), the red diode (7) on the
charger turns on to indicate that the charging is in progress.
At the same time green diodes (9) of the battery level indication are
flashing in different configurations, see description below.
• All diodes are flashing – the battery is empty and requires charging.
• 2 diodes are flashing – the battery is partially discharged.
• 1 diode is flashing – the battery level is high.
Once the battery is charged, the diode (7) on the charger lights green,
and all battery level indication diodes (9) light continuously. After some
time (approx. 15 s) the battery level indication diodes (9) turn off.
Do not charge the battery for more than 8 hours. Exceeding this time
limit may cause damage to battery cells. The charger does not turn
off automatically when the battery is full. Green diode on the charger
will remain on. Battery level indication diodes turn off after some
time. Disconnect power supply before removing the battery from the
charger socket. Avoid consecutive short chargings. Do not charge the
battery after short use of the tool. Significant decrease of the period
between chargings indicates the battery is worn out and should be
replaced.
Batteries heat up when charging. Do not operate just after charging –
wait for the battery to cool down to room temperature. It will prevent
battery damage.
BATTERY LEVEL INDICATION
The battery is equipped with battery level indicator (3 LED diodes)
(9). To check battery level status, press the button for battery level
indication (8) (fig. C). When all diodes are lit, the battery level is high.
When 2 diodes are on, the battery is partially discharged. When only one
diode is lit, the battery is discharged and must be recharged.
INSTALLATION / DEINSTALLATION OF NOZZLE
• To install the nozzle (1) on the blower, slide it onto the stub until the
nozzle lock button (2) snaps on (fig. C) (fig. D).
• To disassemble, press in the nozzle lock button (2) and slide off the
nozzle (1) from the stub (fig. E).
OPERATION / SETTINGS
SWITCHING ON / OFF
Switching on
• Slide the switch (3) forward to position I.
Switching off
• Slide the switch (3) back to position O (fig. F).
OPERATION AND MAINTENANCE
Remove the battery from the device before commencing any
activities related to installation, adjustment, repair or maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device immediately after each use is recommended.
• If possible, motor casing should be always free from dust and dirt.
• Wipe the device with a clean cloth or blow through with compressed
air at low pressure.
• Do not clean with water or chemical cleaning agents.
• Be careful to avoid ingress of water into the device.
• Use only original equipment and original spare parts.
• When not in use, store the tool in a dry place, beyond reach of
children.
• Store the device with the battery removed.
All defects should be repaired by service workshop authorized by the
manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless Leaf Blower 58G031
Parameter
Battery voltage
Motor speed
Air flow speed
Protection class
Weight
Year of production
58G031 defines type and indication of the device
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
8
Value
18 V DC
12000 min
-1
190 km/h
III
1,2 kg
2021
Value
58G001
58G004
18 V DC
18 V DC
Li-Ion
Li-Ion
2000 mAh
4000 mAh
4
C – 40
C
4
C – 40
C
0
0
0
0
1 h
2 h
0,400 kg
0,650 kg
2021
2021
Publicidad
