Makita PW5000C Manual De Instrucciones página 5

WARNING:
Wear ear protection.
WARNING:
The noise emission during actual use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined according to EN62841-2-3:
Work mode: stone polishing
Model
PW5000C
PW5000CH
NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and
may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the
times when the tool is switched off and when it is running idle in addition to the trigger time).
WARNING:
The declared vibration emission value is used for main applications of the power tool. However if
the power tool is used for other applications, the vibration emission value may be different.
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Stone polisher safety warnings
Safety warnings common for polishing operations:
1. This power tool is intended to function as a pol-
isher. Read all safety warnings, instructions, illus-
trations and specifications provided with this power
tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Vibration emission (a ,
h P
5.0
5.0
Operations such as grinding, sanding, wire brushing,
2.
hole cutting or cutting-off are not to be performed with
this power tool. Operations for which the power tool was not
designed may create a hazard and cause personal injury.
Do not convert this power tool to operate in a way
3.
which is not specifically designed and specified by
the tool manufacturer. Such a conversion may result
in a loss of control and cause serious personal injury.
4. Do not use accessories which are not specifically
designed and specified by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
5. The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
6. The outside diameter and the thickness of your
accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
7. The dimensions of the accessory mounting must
fit the dimensions of the mounting hardware of the
power tool. Accessories that do not match the mount-
ing hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
8. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear,
wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an
accessory, position yourself and bystanders away from
the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
5 ENGLISH
2
) : (m/s ) Uncertainty (K) : (m/s
1.5
1.5
2
)