Publicidad
Idiomas disponibles
Idiomas disponibles
4. To position the guard:
One‑touch
TM
: Rotate the guard clockwise into the
desired working position. Press and hold the guard
10
release lever
release lever to rotate the guard in the
anti‑clockwise direction.
Two‑touch
TM
: Press and hold the guard
10
release lever
. Rotate the guard clockwise or
counterclockwise into the desired working position.
NOTE: The guard body should be positioned between
the spindle and the operator to provide maximum
operator protection.The guard release lever should snap
into one of the alignment holes
This ensures that the guard is secure.
5. To remove the guard, follow steps 1–3 of these
instructions in reverse.
Flanges and Wheels
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Mounting Non‑Hubbed Wheels (Fig. H)
WARNING: Failure to properly seat the flange/ clamp
nut/ wheel could result in serious injury (or damage to
the tool or wheel)."
CAUTION: Included flanges must be used with
depressed center Type 27 grinding wheels and
Type 1/41 and Type 27/42 cutting wheels. See the
accessories Chart for more information.
WARNING: A closed, two-sided cutting wheel guard is
re quired when using cutting wheels.
Cutting wheels include diamond wheels and abrasive
discs. Abrasive cutting wheels for metal and concrete
use are available. Diamond blades for concrete cutting
can also be used.
CAUTION: Included flanges must be used with
all non-hubbed accessories except conventional
sanding discs.
WARNING: Use of a damaged flange or guard or
failure to use proper flange and guard can re sult in
injury due to wheel breakage and wheel contact. See
the accessories Chart for more information.
1. Install the unthreaded backing flange
with the raised section (pilot) facing the wheel as shown.
6
2. Place wheel
against the backing flange, centering the
wheel on the raised section (pilot) of the backing flange.
3. While depressing the spindle lock button and with the
hex depressions facing away from the wheel, thread the
8
locking flange
on spindle so that the lugs engage the
two slots in the spindle.
4. While depressing the spindle lock button, tighten the
locking flange with a wrench.
5. To remove the wheel, depress the spindle lock button
and loosen the threaded locking flange with a wrench.
17
on the guard collar.
7
4
on spindle
Mounting Sanding Backing Pads (Fig. I, N)
NOTE: Use of a guard with sanding discs that use backing
pads, often called fiber resin discs, is not required. Since a
guard is not required for these accessories, the guard may or
may not fit correctly if used.
WARNING: Failure to properly seat the clamp nut and/
or pad could result in serious injury (or damage to the
tool or wheel).
WARNING: Proper guard must be reinstalled for
grinding wheel, cutting wheel, sanding flap disc,
wire brush or wire wheel applications after sanding
applications are complete.
1. Place or appropriately thread backing pad
the spindle.
2. Place the sanding disc
3. While depressing spindle lock button
20
sanding clamp nut
hub on the clamp nut into the center of san ding disc and
backing pad.
4. Tighten the clamp nut by hand. Then depress the spindle
lock button while turning the sanding disc until the
sanding disc and clamp nut are snug.
5. To remove the wheel, grasp and turn the backing
pad and sanding pad while depressing the spindle
lock button.
Mounting and Removing Hubbed
Wheels (Fig. J)
Hubbed wheels install directly on the spindle. Thread of
accessory must match thread of spindle.
1. Remove backing flange by pulling away from tool.
2. Thread the wheel on the spindle
3. Depress the spindle lock button
tighten the hub of the wheel.
4. Reverse the above procedure to remove the wheel.
NOTICE: Failure to properly seat the wheel before
turning the tool on may result in damage to the tool or
the wheel.
Mounting Wire Cup Brushes and
Wire Wheels
CAUTION: To reduce the risk of personal injury,
wear work gloves when handling wire brushes
and wheels. They can become sharp.
CAUTION: To reduce the risk of damage to the
tool, wheel or brush must not touch guard when
mounted or while in use. Undetectable damage
could occur to the accessory, causing wires to fragment
from accessory wheel or cup.
Wire cup brushes or wire wheels screw directly on the
grinder spindle without the use of flanges. Use only wire
brushes or wheels provided with a 5/8"‑11 threaded hub.
A Type 27 guard is required when using wire brushes
and wheels.
1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench on the
hub of the wire wheel or brush to tighten the wheel.
ENGlIsh
18
on
19
on the backing pad.
3
, thread the
on spindle, piloting the raised
4
by hand.
3
and use a wrench to
41
Publicidad
