RIKO expero Manual De Instrucciones página 11

OPERATION MANUAL
UNFOLDING THE PRAM
To unfold the pram, put it flat on the ground (Fig. 1), and
pull vividly the handle up until the folding mechanism is locked
(Fig. 2, 3).
NOTE! Before starting to use the pram, make sure that it has been
correctly unfolded.
ASSEMBLING AND DISASSEMBLING THE REAR WHEELS
To disassemble the rear wheels, press down the button in the central
part of the wheel (Fig. 4) and remove the wheels from the axle (Fig. 5).
To assemble them again, press the button down and slide the wheels
onto the axle till they get locked.
NOTE! Before starting to use the pram, make sure that all the
wheels have been assembled correctly.
ASSEMBLING AND DISASSEMBLING
SWIVELLING WHEELS
In order to attach the front wheels, push their hubs into the handles
on the ends of the front tubes (fig. 6). In order to remove the wheel,
press the button on the back of the wheel and pull the hub from the
handle (fig. 7).
SWIVELING FRONT WHEELS
The swiveling front wheels of the stroller can be locked in a straight-
running position. To unlock the wheels, turn the knob located in the
middle of the front suspension clockwise (fig. 8). To lock the wheels,
turn the knob counter-clockwise.
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the
adjustment, press down the round buttons on both sides of the handle
at the upper part, and then adjust the right height (Fig. 9a, 9b).
PARKING BRAKE
The stroller is equipped with a parking brake. To apply the brake,
push the pedal located next to the right rear wheel (fig. 10). To release
the brake, push the pedal located next to the left rear wheel (fig. 10a).
NOTE! Before starting to push the pram, make sure that the brake
has been disengaged.
NOTE! Always engage the safety brake, when you leave the pram
on an inclined surface.
NOTE! The brake is not designed for slowing down. It should be
engaged after the pram has been stopped completely.
NOTE! The pram is not designed for running.
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so that
the adapters on both sides of the carrycot lock onto the catches
on the pram frame (fig. 11). They will lock in place automatically.
ATTENTION! Make sure the carrycot is attached correctly prior
to use.
To remove the carrycot press the buttons on the adapters at the
sides of the carrycot (fig. 12) and pull the carrycot upwards.
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the same way
as for the bassinet (see ASSEMBLING AND DISASSEMBLING THE
BASSINET Fig. 13a, 13b, 13c).
The seat may be assembled with its front and back facing the
movement direction.
NOTE! Before starting to use the pram make sure that the seat has
been assembled correctly.
ADJUSTING THE FOOTREST
The pram is equipped with an adjustable footrest. To move it to the
right position, press down the buttons on its both sides (Fig. 14).
ASSEMBLY AND REMOVING THE BAR
In order to assembly the bar, insert its hooks on the handles on
THE FRONT
the seat side tubes (fig. 15a). In order to remove it, push the buttons
located in the lower part of the handles and slide the clips out (fig. 15b).
There is no need to remove the bar before folding the stroller.
NOTE! Never move the stroller by holding the bar.
NOTE! Using the bar does not exempt from the obligation to use
the seat belts.
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system. It should be
used from the moment a baby starts to sit by itself. Unfasten the belts,
by releasing the forks from the central buckle, seat the baby, adjust the
length of the belts so that they fit closely to the baby's body, without
oppressing it, and then fasten the forks of all the belts to the central
buckle (fig. 16a, 16b, 16c).
The seat has an additional crotch strap which should be attached to
the safety bar using snaps (fig. 17). This is an additional element and
not be a substitute for using the 5 point safety harness.
NOTE! Always use the restraint system, if the baby can sit by itself.
RECLINING SEAT
The seat can be reclined into 4 different positions. To recline the
backrest, unzip the zipper located in the back of the seat (fig. 18a),
then pull the lever situated in the back of the backrest and move the
backrest into the required position (fig. 18b). To raise the backrest,
push it upwards (fig. 18c). The backrest automatically locks in each
position. For better aesthetics, zip back the zipper in the back of the
seat (fig. 18a).
RAIN COVER
The pram comes with a leg rain cover. To put it on start from the
end next to the child and attach it to the canopy using snaps (fig. 19).
BAG
The stroller is provided with a functional bag that can be attached to
the stroller's handlebar (fig. 20).
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole at
the baby's face height. To assemble it, put one end under the footrest
or under the bassinet rear, and pull the other end onto the canopy
(Fig. 21, 21a). The foil is suitable both for the deep and stroller version.
MOSQUITO NET
The stroller is completed with a practical mosquito net. To install the
net, put one end on the canopy and attach it with ties. Then put the
other end of the net on the back of the carriage or the footrest (fig.
22, 22a). The mosquito net can be installed both on the carriage and
the seat.
RECLINING CARRIAGE SUPPORT
The carriage support is reclinable. To recline it into suitable position,
push and turn the knob located under the carriage (fig. 23).
RECLINING CARRIAGE CANOPY
To close the carriage canopy, push down its handle (fig. 24a) and
then push it forward (fig. 24b). To stretch the canopy back, pull the
handle in the opposite direction. The canopy automatically locks in the
vertical position.
VENTILATED CARRIAGE
The carriage is ventilated. To open the vent holes, slide the air grate
located under the carriage (fig. 25).
INSTALLING THE CAR SEAT WITH ADAPTERS
Push the adapters into catches situated on the stroller's frame
(fig. 26) and then push the car seat's catches into the adapters (fig. 27).
The car seat has an adjustable handle. To position it, push the
buttons located at its feet (fig. 28).
REMOVING THE CAR SEAT AND ADAPTERS
To remove the car seat, push both buttons located on its sides
(fig. 29) and pull the handle upwards.
To remove the adapters, push both buttons situated on their inner
side and pull them upwards (fig. 30).
FOLDING THE STROLLER
Remove the carriage or seat before folding the stroller.
Fold the stroller's handlebar at an angle of 180°, using the height
adjustment lever (fig. 31). Position the front wheels so that mudguards
are pointed straight ahead (fig. 32). Then, grab the mechanism located
in the middle of the crossbar, above the storage basket, and push the
mechanism's button (fig. 33). While holding the mechanism, lift the
stroller's frame (fig. 34, 35).
11