Publicidad
Idiomas disponibles
Idiomas disponibles
USE OF AN EXTENSION CABLE
Extension cables must be chosen carefully. Refer to the related safety regulations. To
prevent excessive drops in voltage, use cables that are an adequate size for the load
(minimum section 1,5 mm
).
2
CONNECTING THE LOAD
Connecting the load
Connect an appropriate plug, taken from the user device, to the generator socket after
having started the engine.
WARNING! The load must always be disconnected before turning off the motor.
MAINTENANCE (FIG. G)
WARNING! Each operation indicated below must be carried out while the motor is
off and the load's plug is disconnected.
WARNING! If in doubt, contact an authorised assistance centre.
WARNING! Contact an authorised assistance centre for any operations not included
below.
Cleaning after every use
Take care of your machine and clean it regularly to ensure that it remains perfectly
efficient and has a long lifetime.
Clean the machine using a soft brush or cloth.
Do not spray or soak the machine with water.
Do not use inflammable substances, detergents or solvents as these may damage the
machine beyond repair. The plastic parts are prone to damage by chemical agents.
Spark plug
Check it every 50 hours of use, and replace it if necessary.
See the technical data in reference to the spark plug type.
1. Remove the pipette and unscrew the spark plug using the relative spanner.
2. Examine the spark plug and remove any carbon residue with a metal brush. Replace
the spark plug if the electrode is excessively worn or the insulation is damaged.
3. Measure the distance between the electrodes: it should be between 0.7 and 0.8 mm.
4. Screw the spark plug back in by hand.
5. Secure a used spark plug with around ¼ turn of the spanner, and a new one with
around ½ turn of the spanner.
Air filter
Clean it every 50 hours of use, and replace it if necessary.
If used in dusty environments, clean more frequently.
1. Open the cover of the filter box (Fig. A pos.8).
2. Remove the sponge.
3. Wash it with soap and water and rinse completely.
4. Leave it to dry.
5. Immerse the sponge in clean motor oil.
6. Squeeze it to remove excess oil. If there is too much oil left in the sponge, the
motor could smoke.
7. Place the cover of the box and the relative seal back into position.
Fuel pipes
Make sure that there are no craps in the fuel pipe and that the joints are solid on a
daily basis.
Make sure that there are no fuel leaks.
Replace if necessary.
Petrol cock and fuel filters
Where possible, clean every 100 hours of use.
1. Close the petrol cock (Fig. A pos.4 and Fig. E pos.2).
2. Using a spanner, unscrew the cup on the lower part of the petrol cock.
3. Clean the cup using a non-flammable solvent.
4. Reassemble the cup, taking care with the seal. Replace if damaged.
5. Try to open the cock (Fig. E pos.1) to check that there are no leaks.
Petrol filter on the tank
Clean the petrol filter under the tank's filler cap daily using a non-flammable solvent
(Fig. A pos.2).
Parts inside the motor, muffler, valves, combustion chamber, etc.
Approximately every 300 hours of use, have these parts checked at an authorised
assistance centre.
MOVING THE GENERATOR
WARNING! Before moving the generator, turn off the motor and close the petrol
cock. (Fig. E pos.2)
WARNING! Risk of burning. Some parts could remain hot long after the motor is
turned off.
- 12 -
STORAGE
IMPORTANT! Hot surfaces. Some parts of the machine may stay hot for several hours
after it has been switched off. Wait for it to cool down completely before storing it.
IMPORTANT! Make sure that the storage environment is not damp and/or dusty.
1. Remove all the fuel from the tank.
2. Empty the carburettor tray using the drain screw present on the bottom of the same
(Fig. G pos.1).
3. Replace the motor oil.
4. Pour a few drops of motor oil into the spark plug hole and put the motor in the
compression position.
TROUBLESHOOTING AND PERMITTED OPERATIONS
The motor does not start
- The motor's start switch is on "STOP".
- There is no petrol in the tank: fill it up.
- The petrol cock is closed: open it.
- The filter of the petrol cock is dirty: clean it (see maintenance instructions).
- The petrol pipes are blocked: clean them.
- There is dirt or water in the carburettor tray: clean it (contact an authorised service
center).
- The spark plug does not spark, is dirty or worn: clean or replace it.
- The new spark plug does not spark: contact an authorised service centre.
- Other: contact an authorised service centre.
The motor starts and then stops
- The petrol cap bleed valve is blocked: clean it.
- Dirt in the fuel supply system: clean it.
- Excessive electric load: reduce the load.
- Petrol-oil mixture was not used, causing serious damage to the engine. Bring the
generator to an authorised service centre to check. Warning: damage due to this
kind of negligence is not covered by the warranty.
-Other: contact an authorised service centre.
The generator does not supply current.
- The protection switch on the generator has shifted to the "off" position: the protection
has triggered against the overload reducing the load applied.
- The power switch on the generator moved to "OFF": the trip switch against overload
intervened. Reduce the applied load.
- The power switch on the generator moved to "OFF": The trip switch against overload
intervened. Check for short circuits or faults with the connected appliance.
IMPORTANT! If the machine still fails to function correctly after you have carried out
the above operations, or in the event of anomalies other than those described above,
take the lawnmower to an authorised service centre. Always provide the machine
model and serial number shown on the technical data label and the enclosed sheet.
DEMOLITION
In order to protect the environment, proceed according to the local laws in force.
IMPORTANT! Before demolishing the machine, drain the fuel tank completely and
drain the motor oil, handing it over to a used oil collection centre.
Do not throw the packaging away. Take it to a recycling centre instead.
When the machine is no longer usable or reparable, dismantle the various parts for dif-
ferentiated refuse collection. All the plastic components bear an acronym identifying the
materials they are made from. This can be used when recycling them in the future.
Amendments: The text, figures and data correspond to the standard in place on the date
of printing this manual. The manufacturer reserves the right to update the documentation
if changes are made to the machine, without being bound to any obligations.
No part of this publication and the documentation enclosed with the machine may be
reproduced without written permission from the manufacturer.
WARRANTY
The product is protected by law against non-compliance with the declared characteristics
provided it is used only in the manner described in the instructions, it has not been
tampered with in any way, it has been stored properly, has been repaired by authorized
and, where applicable, have been used only original spare parts.
In the case of industrial or professional use or when using such a guarantee is valid
for 12 months.
To issue a claim under warranty you must present proof of purchase to your dealer or
authorized service center.
Publicidad
