LUND 67500 Manual De Instrucciones página 11

EN
tools. In this case, disconnect the toaster from the power supply by unplugging the power
cord from the socket. Allow the toaster and bread to cool down completely and then carefully
remove the bread from the toast slot using hands or wooden tools. Be careful not to damage
or deform the toaster components when removing bread.
Always unplug the power cord plug from the socket after use. Do not store the appliance
plugged into a socket.
PRODUCT OPERATION
Installation, start-up and operation of the product
The product must be unpacked and all parts of the packaging removed. It is recommended to keep the packaging, as it can be
helpful in further transporting and storing of the product.
Clean the product according to the instructions specifi ed in the "Product maintenance" section.
Make sure the power cord is completely unwound from the housing. Do not use the product with the power cord wound on the
bottom of the housing.
Place the toaster according to the instructions for installing it.
Use the knob to adjust the toasting level. For the fi rst use, it is recommended to set the knob in the middle of the scale and after
observing the eff ects of toasting, change the settings if necessary.
Place the bread into at least one toast slot.
Connect the toaster to the power supply.
Press and lower the toaster push-down lever as far as it will go. If the lever remains in the lower position after releasing it, the
toaster will start toasting. After the toaster has fi nished toasting, it will automatically stop the process and lift the prepared bread in
the toast slots. The toasting process can be interrupted at any time by pressing the button marked "CANCEL".
The toaster has guides that keep the bread at the same distance from the heaters of the product during toasting. Thanks to this
both sides of the bread are toasted with the same intensity and at the same time.
After use, unplug the power cord from the socket.
Allow the product to cool down completely and proceed with maintenance.
The toaster can heat up a toast that has already been toasted without increasing the toasting level. After turning on the toaster as
described above, press the button marked "REHEAT" and the button will be illuminated. Once the toaster has fi nished heating, it
will automatically stop the process and lift the prepared bread in the toast slots. The toasting process can be interrupted at any
time by pressing the button marked "CANCEL".
The toaster can defrost and heat up the toast. After turning on the toaster as described above, press the button marked "DE-
FROST" and the button will be illuminated. Once the toaster has fi nished heating, it will automatically stop the process and lift the
prepared bread in the toast slots. The toasting process can be interrupted at any time by pressing the button marked "CANCEL".
WARNING! During and immediately after operation: the housing and metal parts heat up to a high temperature. Caution must be
maintained. Contact with hot product parts can lead to serious burns.
Product maintenance
CAUTION! All maintenance works must be carried out with the product switched off . To do this, unplug the power cord from
the socket.
CAUTION! Never immerse the product in water or any other liquid. The product cannot be cleaned under running water, high-pres-
sure water jet or in a dishwasher.
CAUTION! Allow all parts of the product to cool down completely before carrying out maintenance work.
At the bottom of the toaster housing there is an extendible crumb tray. Remove and clean the tray after each use of the toaster.
Depending on the model, the tray is extended or pressed and then released and extended (II). Clean the tray under a stream of
running water with a small amount of dishwashing liquid, then dry and insert it into the slot in the toaster housing. Do not clean the
crumb trays in a dishwasher or with a high-pressure water jet.
Clean the toaster housing with a soft, slightly damp cloth and then wipe dry.
Clean the inside of the toaster by turning it upside down with the slots downwards and shake the crumbs, slightly rinsing the bottom.
Do not use abrasive, caustic, alcohol, solvents, etc. cleaning agents for toaster maintenance.
Product storage and transport
The lower housing of the product allows the power cord to be woven for storage (III).
During storage, keep the product indoors in closed rooms, and make sure it is not exposed to dust, dirt, or moisture. It is recom-
O R I G I N A L I N S T R U C T I O N S
11