YATO YT-82920 Manual De Instrucciones página 12

GB
charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange
smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket!
The drill and automatic return screwdriver is provided with an unloaded battery, so before work may commence, it is required
to charge it following the procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so
called "memory eff ect", so it is allowed to charge them at any moment. However, it is recommended to discharge them during
normal work, and then load them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it
is required to do it at least from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the
electrodes, since this would cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the
electrodes for sparking.
Storage of the battery
In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through ap-
proximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the relative humidity of 50%. In
order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of prolonged
storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this would
reduce its life and may cause irreversible damage.
During storage, the battery will be gradually unloading due to leakage conductance. The process of automatic unloading depends
on the temperature of storage, since the higher the temperature, the fastest the process. In case of incorrect storage of batteries,
there is a danger of electrolyte leakage. In case of leakage, it is required protect the leakage with neutralizing agent. In case of
contact of electrolyte with the eyes, it is required to rinse the eyes abundantly, and then immediately seek medical assistance. It
is prohibited to use a tool with a damaged battery.
In case the battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.
Transport of the batteries
Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the
tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third
parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport
of dangerous materials. Before shipment, contact an authorised person.
It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed
contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It
is also required comply with the national regulations for transport of dangerous materials.
Charging the battery
Attention! Before charging you should disconnect the charger from the mains by unplugging the power supply plug from the mains.
In addition, you should clean the battery and its terminals of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. When you press the button, LEDs will light up (II), the more LEDs will light up, the more
fully the battery pack is charged. If the button is pressed and the LEDs are off it means that the battery is discharged.
Disconnect the battery from the tool.
Push the battery in the charger socket (II).
Plug the charger into a mains socket.
When the red LED lights up, it means the loading process.
When charging is complete, the red LED goes off , and green LED lights up, indicating a full charge of the battery.
Unplug the charger from the mains outlet.
Remove the battery from the charging station, by pressing the battery latch button.
Attention! If, when the charger is connected to the power supply, the green LED is on, this indicates a fully charged battery. In this
case, the charger does not start charging.
Installation of polishing pads (III)
The polishing disc has a Velcro, which allows the attachment of polishing pads, covers and polishing sponges with a special sur-
face which can be attached to the Velcro of the disc. The pads should be attached concentrically, do not allow the surface of the
Velcro disc to come into contact with the polished surface. This can damage both the disc and the polished surface.
Adjustment of rotational speed (IV)
The polisher has a speed control by means of a rotary controller placed above the switch. It is possible to smoothly adjust the
rotational speed within the range specifi ed in the table with technical data. Lower rotation should be applied for initial application
of polishing paste, after spreading it on the polished surface, increase the rotational speed. When polishing without a paste, apply
high rotational speed.
O R I G I N A L I N S T R U C T I O N S
12