Getting started
Wash Options
F
SmartDispense™ - Detergent
When selected, this feature will automatically add detergent to the wash based on the load size, eliminating the
need to add detergent for each load. Multi-tapping this button will step through dosing levels of AUTO, MORE,
and LESS (levels visualized on the LCD screen and the LED indicator next to the button will be ON) and OFF
(level shows off on the LCD and the LED indicator will be off). The Combo also has Adaptive SmartDispense
capability through the SmartHQ App. With this enhancement, you can select the specific type of detergent
and, in addition to using load size information, it will adjust the dosage based on the detergent manufacturer's
recommendations. See the SmartDispense - Detergent section for details.
SmartDispense™ - Softener
When selected, this feature will automatically add softener to the final rinse based on the load size, eliminating
the need to add softener for each load. Multi-tapping this button will step through dosing levels of AUTO,
MORE, and LESS (levels visualized on the LCD and the LED indicator will be ON) and OFF (level shows off on
the LCD and the LED indicator will be off). The Combo also has Adaptive SmartDispense capability through
the SmartHQ App. With this enhancement, you can select the specific type of softener and, in addition to using
load size information, it will adjust the dosage based on the softener manufacturer's recommendations. See the
SmartDispense - Softener section for details.
PreWash
Prewash is an extra wash before the main wash. Use it for heavily soiled clothes or for clothes with a care label
that recommends prewashing before washing.
NOTE: Detergent from PreWash can only use detergent from the SmartDispense detergent tank. SmartDispense
will automatically add the proper amount of detergent for prewash based on the load size. If you choose to
deselect SmartDispense detergent to support a manual detergent dose, the PreWash cannot be activated.
PreWash must be selected prior to pressing Start.
The PreWash feature will fill the Combo (adding the prewash detergent), tumble the clothes, drain and spin.
Then the Combo will run the selected cycle.
NOTE: In some special cycles, PreWash is selected automatically as the default. You can turn off this selection
at any time. The main wash will use new detergent from either the manual detergent compartment or from the
SmartDispense tank if SmartDispense is selected. If you activate it, do not add additional detergent.
More Water
This option adds up to approximately 3 gallons to the wash and rinse portions of the cycle. If the option is
selected before the cycle starts, the water will be added from the beginning of the cycle and later to the rinse.
If the option is selected during the wash portion, more water will be added at this point and later to the rinse.
Likewise, if the More Water option is selected after the wash portion has completed, the Combo will add more
water to the rinse only. If wash and rinse have completed, the More Water button will no longer be active.
Remote Start
After choosing the cycle and the desired options, press and hold for 3 seconds the More Water/Remote Start
button to allow the Combo to start a cycle from the SmartHQ app. The LCD screen will show a purple box as
the first sequence before the blue WASH and /or magenta DRY operations for that cycle to indicate that the
Combo will await your command to begin the cycle. It is important to hit the Start/Pause button to confirm
that you want to activate Remote Start fully. You will hear the drain pump pulse twice and the door locking to
indicate that the Combo is synchronized with the App.
To cancel Remote Start, you can either press and hold the More Water/Remote Start button once again or
Power Off the Combo.
Remote Start can also be initiated from with the Menu under the Delay Start item by turning it On from there.
Extra Rinse
This option allows for an extra rinse during a cycle to remove excess dirt and detergent from soiled loads.
Press the Extra Rinse button to select.
10
49-3000353 Rev 3