Care And Maintenance - Steinbach Speedcleaner APPcontrol Manual De Instrucciones

Pool cleaner components
Fig. 3:
1) Handle
2) Filter unit
3) Drive roller
4) Bearing for drivel roller
5) Drive belts
6) Side cover
7) Floating cable
8) Engine unit
9) Drive wheel
10) Propeller
11) Nozzle insert
12) Frame
13) Top cover
14) Power supply
Preparation
Place the cleaner into the water, while holding onto the hanging ring
(Fig, 4). Once all the air has escaped from the cleaner, (the cleaner
must be completely free of air, otherwise normal operation will be affect-
ed), it will sink to the bottom on its own.
Caution: For optimal performance, make sure that there is no more air
in the cleaner (air bubbles stop coming out of the cleaner, and it stays
on the pool fl oor properly).
Connecting the power source
When the cleaner is completely on the pool fl oor, take the power cable,
roll it out fully and push the plug into the socket on the power supply.
Then connect the cable to the socket (Please note when connecting
cables that the plugs are in the right direction and position in relation
to each other), and tighten the nuts on both sides. Connect the mains
cable to the power source. The swimming pool cleaner is now ready for
use.
Panel
NO. Sign Indicate
Switch on
1 ON/OFF
or off
Mode op-
tions
Fig. 5
Fig. 6
2 Mode
Fig. 7
Fig. 8
Working
duration
option
3 Time Fig. 9
10
Function
■ Press this button machine will be
switched on.
■ Press this button twice machine
will work under selected mode.
■ Press this button third time ma-
chine will be switched off.
Choose different mode for differ-
ent purpose.
"ALL"mode is let machine
clean swimming pool fl oor
wall and water line together.
(once wall then once fl oor)
"WALL" mode is let machine
clean swimming pool
wall only.
"FLOOR" mode is let machine
clean swimming pool
fl oor only.
"ALL + FLOOR" mode is let
machine clean the swimming
pool fl oor three times
then climb wall once.
Different working duration for
different purpose
1H 2H 3H
Indicate different working duration
Indicate the machine status
Two or three indica-
tors on
1H fl ash slowly
2H fl ash slowly
3H fl ash slowly
ALL light on
WALL light on
FLOOR light on
Working
4 Indicator
status
ALL + FLOOR light on
ALL>>WALL>>FLOOR
fl ash in order
FLOOR>>WALL>>ALL
fl ash in order
3H>>2H>>1H fl ash in
order
1H>>2H>>3H fl ash in
order
All lights fl ash slowly
You can also control the Speedcleaner APPcontrol using the APP.
Please use the following link (Android + IOS): Fig 14.
Bluetooth for smart phone
(optional) (Fig. 10)
NO. Indicator Function
■ disconnected
1 Bluetooth status
■ connected
Press to start searching Bluetooth
2 Searching signal
signal.
3 ▲ Manual walking forward
4 ▼ Manual walking backward
5 ◄ Manual left turn
6 ► Manual right turn
7 Stop sign Manual stop machine
■ Pool fl oor mode
■ Pool wall mode
8 Mode
■ One fl oor one wall mode
■ Three fl oor one wall mode
■ Auto Play: working as selected mode
9 Auto play or stop
■ STOP: stop working automatically
Attention: "►"&"◄"need to be pressed constantly

Care and maintenance

The cleaner turns itself off automatically after a cleaning cycle. Unplug
the mains cable, gently pull the cable, and lift the cleaner out of the
water using the ring on the clamp nut.
Caution:
When lifting the cleaner out of the water, you must ensure that the
cleaner does not hit the side of the pool wall, otherwise you may dam-
age both the cleaner and the liner.
061023_v1901 EN
Machine stopped
Machine running
for 1 hour
Machine running
for 2 hour
Machine running
for 3 hour
Working under
mode ALL
Working under
mode WALL
Working under
mode FLOOR
Working
under mode ALL-
FLOOR
Manual: forward
Manual: back-
ward
Manual: left turn
Manual: right
turn
Auto run
fi nish
.