Publicidad
Idiomas disponibles
Idiomas disponibles
MIXER SECTION:
CHANNEL INPUT SELECTOR: The CHANNEL INPUT SELECTOR switches allow
29
you to choose which input will be controlled by that channels corresponding vol-
ume FADER. For example CHANNEL (1) INPUT SELECTOR allows you to choose
between line (1) (That sides internal CD player), line (2) which is line input RCA
(1) and or PHONO (1) (if the CONVERTIBLE LINE SWITCH is switched to
PHONO) see above. The same applies for channel 2.
CHANNEL ROTARY GAIN: The CHANNEL ROTARY GAIN allows you to boost
30
the signal of each individual channel depending on how low or high its input
level is.
3 BAND EQUALIZER: The 3 BAND EQUALIZER adjusts the tone of each CHAN-
31
NEL by giving you a choice 3 frequencies (BANDS) to adjust , from LOW,
MIDRANGE (MID) and HIGH's ,you can use the adjustment knobs to higher or
lower the 3 separate frequencies till the sound of the music program is appro-
priate for your listening environment.
CHANNEL VOLUME FADER: After you have chosen which input you will use with
32
the INPUT SELECTOR the corresponding CHANNEL FADER will allow you to ad-
just the volume for that particular CHANNEL.
CHANNEL CUE SELECTOR: The CHANNEL CUE SELECTOR allows you to choose
33
which channel you wish to monitor in your headphones, to the left is CHANNEL
(1) to the right is CHANNEL (2).
CUE VOLUME ROTARY KNOB: The CUE VOLUME ROTARY KNOB adjusts your
34
HEADPHONE MONITOR OUTPUT'S volume.
MICROPHONE VOLUME ROTARY KNOBS: Allow you to adjust the
35
volume of the of either of the (2) microphone outputs separately and are lo-
cated on the front panel of the CDM-3700G. MIC ROTARY (1) controls MIC
CHANNEL (1) and MIC ROTARY (2) controls MIC CHANNEL (2).
MASTER OUTPUT ROTARY KNOB: The MASTER OUTPUT rotary knob adjust
36
the volume of the MAIN MASTER output.
VU METER: The CDM-3700G has a stereo VU METER that allows you to monitor
37
the decible levels of the LEFT and RIGHT MASTER output.
FADER START BUTTON: The Fader Start function allows you to start CD play-
38
back simply by moving the CROSSFADER from side to side.
A. Cue up the CD player you wish to start using the Fader Start function
B. Move the CROSSFADER all the way to the opposite side of the CD
you have just Cued.
C. Press the FADER START SELECTOR button so that the button
becomes illuminated.
D. At the point which you wish to start the audio from the Cued CD,
simply move the CROSSFADER in the direction of the Cued CD player,
and playback will begin.
E. When the CROSSFADER is moved all the way to the opposite side of
the currently playing disc, the unit will stop playing that disc and return to
the beginning of the track or the set cue point.
CROSS FADER: The CROSS FADER allows you to mix evenly from one source to
39
another. The CROSS FADER on the CDM-3700G is also removable and if the
need arises can be replaced.The RG-45 (RAILGLIDE
FADER, which has internal dual stainless steel rails that allow the slider to ride
smoothly and accurately from end to end can be purchased from your local
GEMINI dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE THE FADER BACK AND
FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS AND CAUSE A
LOSS OF SOUND.
40
41
42
™
) DUAL-RAIL CROSS
CDM-3700G
VIDEO OUTPUT
VIDEO OUTPUT SECTION has three different video outputs, the CD1 and
CD2 outputs will display either CD CHANNEL 1 or CD CHANNEL 2 individu-
ally, and the (3) AUTO video outputs will all display the same video signal
and are directly connected to the CROSSFADER, so when you move the
CROSSFADER to the left the AUTO VIDEO OUTPUTS will display the video
signal from CD CHANNEL (1) and when slide the CROSSFADER to the right
the AUTO VIDEO OUTPUTS will display the video signal produced by CD
CHANNEL (2).
NOTE: THE THREE AUTO VIDEO OUTPUTS ALL DISPLAY THE SAME VIDEO SIGNAL AND ARE
ALL CONTROLLED BY THE CROSSFADER
VIDEO SELECT SWITCH: The VIDEO SELECT SWITCH determines which of the
VIDEO outputs will be used, in CD1 or CD2 mode it will only activate either
one of those outputs individually. In AUTO mode the three AUTO VIDEO
OUTPUTS will display either CD1 or CD2 depending on the position of the
CROSSFADER.
MIC EFFECT
The MIC EFFECT controls will allow you to add an ECHO/DELAY
effect to both MIC CHANNELS at the same time and have three dif-
ferent settings:
DELAY:
Adjusts the timing of the ECHO and will determine how fast
or how slow the ECHO repeats.
REPEAT:
Adjusts how many times or "how Long" the ECHO will keep repeating
ECHO:
Will control the level for this effect in relation to the dry signal from
microphone channel (1) and (2)
FADER REPLACEMENT:
1. UNSCREW THE FADER (B) SCREWS. DO NOT TOUCH INSIDE SCREWS (C) CARE-
FULLY
REMOVE OLD CROSS FADER AND UN-
PLUG CABLE (D)
2. PLUG IN THE NEW CROSS FADER
INTO CABLE (D) AND PLACE BACK INTO
MIXER.
3. SCREW THE CROSS FADER TO MIXER
WITH THE FADER PLATE SCREWS (B)
4. REPLACE THE FACE OF THE MIXER AND
SCREW THE FOUR SCREWS BACK IN AND RE-
PLACE THE FADER KNOBS.
6
Publicidad
