Sony SRS-ZP1000 Manual De Instrucciones

Active Speaker System
Operating Instructions
Manual de instrucciones
SRS-ZP1000
2005 Sony Corporation
Owner's Record
The model number and the serial number are located on the rear of the left speaker.
Record the model number and the serial number in the space provided below. Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. SRS-ZP1000
Serial No.
A
Right speaker (rear)
Rch IN
Be sure to match the + (red) and –
(black) wires and connectors for the left
and right speakers.
B
Right speaker Left speaker
(rear) (rear)
to INPUT2 jack
Connecting cord
(not supplied)
to INPUT1 jack
to wall outlet
Connecting cord (supplied)
About the INPUT 1 and INPUT 2 jacks
Connect to a CD/MD Walkman* and PC etc., with a headphones
jack or LINE OUT jack. When the component has both a
headphones jack and a LINE OUT jack, connect to the LINE OUT
jack of this system. If you connect to the headphones jack of this
system, turn down the connected component volume level to
prevent audio distortion.
C
Left speaker
(front)
D
Left speaker
(front)
2-318-426-12(1)
Printed in Malaysia
Left speaker (rear)
Rch OUT
To LINE OUT or
to headphones
jack (stereo mini
jack)
CD/MD
Walkman*, etc
To LINE OUT or
to headphones
jack (stereo mini
jack)
PC, etc.
* "WALKMAN" is a registered
trademark of Sony Corporation to
represent Headphone Stereo
products.
PC, CD or
MD Walkman, Right speaker
etc. (front)
POWER
SOUND MODE
BASS
VOLUME
PHONES
MOVIE MUSIC
MIN MAX MIN MAX
POWER SOUND MODE BASS VOLUME PHONES
English
Before operating the unit, please read this manual
thoroughly and retain it for future reference.
WARNING
To prevent fire or shock hazard, do not expose the unit
to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
To prevent fire, do not Cover the ventilation of the
apparatus with news papers, table-cloths, curtains, etc.
Do not place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects filled
with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
CAUTION
You are cautioned that any changes or modification not
expressly approved in this manual could void your
authority to operate this equipment.
NOTICE FOR THE CUSTOMERS IN THE USA
This symbol is intended to alert the user to
the presence of uninsulated "dangerous
voltage" within the product's enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Precautions
On safety
The nameplate indicating operating voltage, power
consumption, etc., is located on the rear exterior.
• Before operating the system, be sure that the operating
voltage of the system is identical with that of your local
power supply.
Where purchased
U.S.A./Canada
European countries
Other countries
• The unit is not disconnected from the AC power source
CD/MD
(mains) as long as it is connected to the wall outlet, even
player, etc.
if the unit itself has been turned off.
• Unplug the system from the wall outlet if it is not to be
used for an extended period of time. To disconnect the
cord, pull the cord by grasping the plug. Never pull the
cord itself.
• Should any liquid or solid object fall into the system,
unplug the system's power cord and have the system
checked by qualified personnel before operating it any
further.
• The AC power cord should be changed only at a
qualified service shop.
• For efficient heat dissipation, ensure there is sufficient
space to the rear of the left speaker. Also, avoid placing
objects on the unit.
• Do not insert your hand or any objects into the hole of
speaker.
On operation
• Do not drive the speaker system with a continuous
wattage exceeding the maximum input power of the
system.
• Before connecting, turn off the Speaker system, the PC
and the audio component to avoid damaging the speaker
system.
• The volume level should not be turned up to the point of
distortion.
• Although this system is magnetically shielded, do not
leave recorded tapes, watches, personal credit cards or
floppy disks using magnetic coding in front of the
system for an extended period of time.
If the TV picture or monitor display is
magnetically distorted
Although this system is magnetically shielded, there may be
cases that the picture on some TV sets/personal computers
may become magnetically distorted. In such a case, turn off
the power of the TV set/personal computer once, and after
15 to 30 minutes turn it on again. In the case of a personal
computer, take appropriate measures, such as data storage,
before turning it off.
When there seems to be no improvement, locate the system
farther away from the TV set/personal computer.
Furthermore, be sure not to place objects in which magnets
are attached or used near the TV set/personal computer,
such as audio racks, TV stands, toys etc. These may cause
magnetic distortion to the picture due to their interaction
with the system.
On placement
• Do not set the speakers in an inclined position.
• Do not leave the system in a location near heat sources,
or in a place subject to direct sunlight, excessive dust,
moisture, rain or mechanical shock.
On cleaning
Do not use alcohol, benzine, or thinner to clean the cabinet.
If you have any questions or problems concerning your
speaker system, please consult your nearest Sony dealer.
Hooking up the system
1
Connect the left speaker to the right
speaker with the supplied cable.
(see fig. A)
Be sure to match the + (red) and – (black) wires and
connectors for the left and right speakers.
Note
Do not connect any other speakers to this system. A
malfunction of this system or the connected
component may result. The sound will not be
produced if you miss-connect the + and – wires and
connectors.
2
Connect the left speaker to the source
equipment.
When the system is connected to the monaural jack of
a radio, etc., the sound may only come through the
left speaker. In such a case, use the optional Sony
plug adaptor PC-251MS. The sound will come
through both speakers.
To connect to a stereo phone-type
headphones jack
Use the optional PC-234HS plug adaptor or RK-G22
connecting cord.
Note
To switch INPUT1 and INPUT2, use ON/OFF of the
device connected to the speakers.
3
Connect the left speaker to the wall outlet.
4
Position the speakers.
Listening to the sound
First, turn down the volume on the left speaker. The
volume should be set to minimum before you begin
playing the programme source.
1
Press POWER on the left speaker.
The POWER indicator lights up.
2
Adjust the VOLUME control.
When connecting to the headphone output, also
adjust the volume of the connected component.
After listening, press the POWER switch
(4 OFF).
The POWER indicator goes off.
To adjust the bass volume level
Turn the BASS dial on the left speaker to adjust the
bass volume. Set the bass volume to an undistorted
level to prevent system damage.
On the sound mode
You can enjoy the best performance of the source by
using the SOUND MODE dial.
– MOVIE: enjoy movies or games on the PC with full
– MUSIC: enjoy music with clear fidelity.
The system can recognize strong sounds and change
the frequency for each sound mode. You can get the
best bass frequency for each sound mode by turning
the BASS dial.
Operating voltage
120 V AC, 60 Hz
220 – 230 V AC, 50 Hz
• 110 – 120 V AC, 50/60 Hz
• 220 – 230 V AC, 50 Hz
3
Using headphones/earphones
Connect headphones/earphones to the PHONES
jack.
Note
Turn off the MEGA BASS or BASS BOOST
(Walkman, etc.) function as it may cause audible
distortion.
Troubleshooting
Should you encounter a problem with your speaker
system, check the following list and take the indicated
measures. If the problem persists, consult your nearest
Sony dealer.
There is no sound from the speaker system.
• Make sure all the connections have been correctly made.
• Make sure the volume on the left speaker and the
connected component have been turned up properly.
• Check if headphones are connected. If they are,
disconnect them.
The sound is distorted.
• Turn down the volume level on the connected
component. Or, if the connected component has the bass
boost function, set it to off.
• Rotate VOLUME on this unit to reduce the volume.
There is hum or noise in the speaker output.
• Make sure all the connections have been correctly made.
• Make sure none of the audio components are positioned
too close to the TV set.
The sound has suddenly stopped.
Make sure all the connections have been correctly made.
The brightness of the POWER indicator is
unstable.
The brightness of the POWER indicator may become
unstable when the volume is turned up. This is not
malfunction.
Specifications
Speaker section
Speaker system
Speaker units
Enclosure type
Impedance
Amplifier section
Rated output
Input impedance
Input
General
Dimensions (w/h/d)
Mass
Cord length
Power consumptions
Cord length
Optional accessories
Connecting cord RK-G22
Plug adaptor PC-234HS, PC-251MS
Design and specifications are subject to change without
notice.
(see fig. B)
(see fig. C)
(see fig. D)
bass tones and clear high tones.
MUSIC
MOVIE
BASS control image
Frequency
2 way
10 cm, cone type
2.5 cm, cone type
Bass reflex
4 Ω
25 W + 25 W (10 % T.H.D., 1 kHz, 4 Ω)
4.7 kΩ (at 1kHz)
Stereo mini jack × 2
(INPUT 1, INPUT 2)
Approx. 140 × 330 × 203 mm
× 13 × 8 in.)
(5 5 ⁄
8
Approx. 4,500 g (9 lb. 15 oz.) (L ch),
approx. 2,800 g (6 lb. 3 oz.) (R ch)
Approx. 1.5 m (L to R)
21 W
Approx. 2 m (power cord)