Brew Strength Selection; Automatic Start Brewing Coffee; Setting The Duration Of The Keep Warm; Auto Shut Off - Bella 14015 Manual De Instrucciones

Brew strength selection

Gourmet strength coffee.
The gourmet setting adjusts the brewing cycle of a full pot of coffee to extract a higher percent of soluble. This
results in a more flavorful pot of coffee.
Bold strength coffee
The Bold setting adjusts the brewing cycle of a full pot of coffee, allowing more time for the coffee to "steep" to
extract further oils and flavor from the coffee bean. This results in a bolder tasting pot of coffee.
1-4 cup brew cycle
Automatically adjusts the brewing process for maximum flavor when brewing small quantities. Ideal for brewing
1 to 4 cups of coffee.
* If 12 cups of water are poured into the water tank then 12 cups of coffee will brew.
1. Press button once to enter into the Brew strength selection mode. The LCD will flash
. To choose between strengths, push the
is . To confirm the selection push
2. To select Gourmet strength coffee, press
The LCD will flash strength. Use the
push button. The coffee maker will beep.
3. To select Bold strength coffee, press
The LCD will flash strength. Use the
push button. The coffee maker will beep.
4. To select the 1-4 cup, press and hold the

Automatic start brewing coffee

Press button once, the LCD screen will display the
saved). The default future brew time is 12:00 AM. Follow the "Setting the clock" to set the HOUR and the MINUTE.
After completion of setting the pre-set clock, the coffee maker will beep and display the auto-start time for 3
seconds before switching to the current time. The LCD will also display the
reaches the set time for the auto brew, the coffee maker will start the brewing cycle.
To cancel the automatic start brewing cycle; simply push on the
disappears.
Remembering your Automatic Start Brew Preferences
Press and hold the
The icon will appear. The coffee maker will begin to brew coffee at the pre-set time. To cancel, press and
hold button for 3 seconds and the
Pause and Serve
If you wish to serve a cup of coffee before the brew cycle is completed, simply remove the carafe from the keep
warm plate. Dripping will automatically cease. Return the carafe onto the keep warm plate; dripping will resume.
CAUTION: To prevent injury when utilizing the pause and serve feature, replace carafe within 30 seconds after
removing during the brewing process.
1. After approximately 2 cups of coffee have been brewed, the carafe may be slowly removed and the coffee
will stop dripping.
2. The flow valve is located on the bottom of the filter holder and is activated when the carafe is removed.
This design makes it possible for you to remove the carafe and pour a cup of coffee before the entire
carafe is brewed.
IMPORTANT: When replacing the filter holder, the flow valve must be properly inserted into the front hole of the
machine, so that it can be seen as it sits on the top of the carafe lid.
3. When using this feature, make sure that the carafe is replaced under the filter holder within 30 seconds to
prevent overflow.

Setting the Duration of the Keep Warm

Press button once, the LCD will display "2:00" and
If you have already set a duration of time for the keep warm, this will be the new default so long as the coffee
maker stays plugged in. To select the period of keep warm time toggle between the
the button is pushed the keep warm time is increased or decreased by increments of 30 minutes. The keep warm
time is between 30 minutes to 4 hours. Once the desired keep warm time is reached, press
confirm. At that time, the coffee maker will beep.

Auto shut off

The coffee maker will automatically shut off once the keep warm time has elapsed after brew.
and
and
button for 3 seconds to recall the last automatic start brew settings that were programmed.
and buttons. The default setting is Regular which
button. The coffee maker will beep.
button to enter into the Brew strength selection mode.
buttons until
button to enter into the Brew strength selection mode.
buttons until
button. One beep can be heard and the LCD will display
icon the and previously set hour will flash (last
button once more until the
icon will disappear.
will flash. The default keep warm time is "2:00" .
6
is selected. To confirm the selection
is selected. To confirm the selection
icon. Once the current time
and buttons. Each time
button again to
. and
.
icon