Publicidad
Idiomas disponibles
Idiomas disponibles
press PGM and the CDX-2200 will be ready to set your next
selection. Repeat the previous steps until you have complet-
ed your play list, then press play to begin the set list.
SINGLE: Pressing the SINGLE button engages SINGLE
11
mode, in this mode the CDX-2200 will play one song and
then stop. Pressing the SINGLE button again will then acti-
vate CONTINUOUS mode causing the unit to play continu-
ously (after the last track, the unit will return to the first track
of the disc and continue to play).
TIME: The TIME button switches the time display between
12
three available sources, these three are TIME ELAPSED on
the track, TOTAL REMAIN on the disc and REMAIN on the
track. TIME ELAPSED indicates how much time has cur-
rently gone by since the play button was pressed, TIME RE-
MAING ON DISC will count down the time remaining on the
entire disc and TIME REMAINING ON TRACK counts down
the time that is left before the end of the track.
PITCH: Press the PITCH button to activate the PITCH CON-
13
TROL SLIDE. Pitch range that can be controlled through the
use of the PITCH CONTROL SLIDER. Press the PITCH but-
ton again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL
14
SLIDE up or down will change the pitch percentage +/ -
12%.
PITCH BEND: Pushing the PITCH BEND BUTTONS will au-
15
tomatically raise the pitch up to +16% or lower the pitch down
to -16% from the existing pitch setting. Releasing the buttons
will return the pitch to the original pitch setting. You can use
this function to match the beat when mixing from one song
to another.
LOOP SECTION: A LOOP repeats the section between the
16
entry point (LOOP IN) and the exit point (LOOP OUT).
A. To set a loop while the unit is playing, start by pressing
the LOOP IN BUTTON (it will light up)
B. When you reach the desired end loop point press the
LOOP OUT BUTTON (it will also light up). The LOOP IN
and LOOP OUT buttons will blink. The loop will continue
playing until you press the LOOP OUT BUTTON again
allowing the music to continue from that point on.
C. To re-engage the loop you must press the RELOOP
BUTTON.
D. When you have released your loop the LOOP IN and
LOOP OUT BUTTON buttons will turn OFF and the will
remain lit to indicate that your loop is stored in the CDX-
2200 memory.
E. Pressing the LOOP IN BUTTON again while the unit is
playing will erase the previously saved loop while saving
your new loop entry point.
F. Press LOOP OUT to exit the loop and save a new com-
plete loop.
G. Press RELOOP to return to the beginning of the previ-
ously saved loop from normal play. Press RELOOP repeat-
edly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT
POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON
17
causes the operation to change from PLAY to PAUSE or from
PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit
when in PLAY mode, while it blinks in PAUSE mode.
CUE: To set a CUE point, press the PLAY / PAUSE BUTTON
18
while a file is playing, and use the JOG WHEEL to adjust the
file to a desired point in the track. Pressing the PLAY / PAUSE
BUTTON will set a CUE point. While the unit is playing and
after the cue point has been programmed, pressing CUE will
cause the CD player to enter the PAUSE mode (PLAY/PAUSE
BUTTON blinks) at the programmed cue point (the CUE LED
is lit). Holding down the CUE button changes the function to
preview, and allows you to stutter start or play from the pro-
grammed CUE POINT. Releasing the CUE button will return
the CD to the preset CUE point.
TRACK SEARCH: The TRACK SEARCH buttons let you se-
19
lect the track to play. +10 allows you to scan through the track
selection in increments of 10.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,
YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE
POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER
AGAIN, THE CUE WILL BE PRESET TO THE BEGINNING
OF THE NEWLY SELECTED TRACK.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded cor-
rectly (label side up). Also check the disc for excessive dirt,
scratches, etc.
- If the disc turns but there is no sound, check the cable con-
nections, if they are ok, check your amplifier or receiver.
-If the CD skips, check the CD for dirt or scratches. Do not as-
sume that the CD player is defective. Many CD's are recorded
out of spec and will skip on most or all CD players. Before
sending the unit for repair, try playing a CD that you are sure
plays properly.
CDX-2200
5
Publicidad
