Publicidad
Idiomas disponibles
Idiomas disponibles
PREPARATION FOR USE
UNPACKING
Do not bend from this side.
CONNECTIONS
Plug the incoming cable into the ANT jack on the rear of the TV.
Cable
Antenna
OR
TV signal
Incoming cable from home Antenna /
Cable Company (No Cable Box)
Cable Box or
Satellite Box*
OR
OUT
IN
Incoming cable from Cable
Company or Satellite Antenna
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU'AU FOND.
Note:
•
For your safety and to avoid damages to the unit, unplug the antenna cable from the
ANT jack before moving the unit.
[EXTERNAL CONNECTION]
VIDEO1 input
(OUT)
ex.
Audio Cable
(OUT)
Video Cable
Video Cassette
OR
(OUT)
Recorder
S-Video Cable
Notes:
The AUDIO L jack is for mono input. The sound is heard from both speakers. Use this jack for
●
connecting monaural audio equipment.
The S-VIDEO jack is given priority over the VIDEO jack.
●
VIDEO2 input
ex.
(OUT)
Audio Cable
Video Camera
(OUT)
Component
Video Game
Video Cable
Notes:
This TV can accept 480p / 480i / simplified 1080i video signal.
●
Simplified 1080 video signal differs to the original 1080i video signal because it is displayed
●
after converted into 480p signal.
INSTALLING THE BATTERIES
1
2
3
[BATTERY PRECAUTIONS]
• Be sure to follow the correct polarity as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
All manuals and user guides at all-guides.com
The stand of this TV is folded when you pur-
chased. Place this TV face-down on a flat sur-
face covered with the soft cloth. Bend the
stand slowly to forward until it clicks.
If you want to fold the stand again, insert a
thin rod into the hole in the right side of the
stand as illustrated, bend the stand backward
while you keep pushing the hole.
Rear of this TV
AN T
*NOTE (DO NOT DISCONNECT FROM BOX)
Some cable TV systems use scrambled signals
and require a special converter to receive these
channels. Consult your local cable company.
Rear of this TV
(IN)
(IN)
(IN)
Rear of this TV
(IN)
(IN)
Install two AAA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote con-
trol.
INITIAL SETUP
When you turn on the power for the first time, the "SELECT LANGUAGE" menu is displayed.
The "INITIAL SETUP" menu is displayed every time you turn on the unit unless the scanning is completed.
1
1
Select the desired
SELECT LANGUAGE
language according to
ENGLISH
NEXT:PRESS CHK
ESPAÑOL
DESPUÉS:PRESIONE CHL
the screen indication.
FRANÇAIS
APRÈS:PRESSEZ VOLX
After that, the TV
performs "AUTO
PRESET CH" to scan
– INITIAL SETUP –
channels available for
PLEASE CONNECT ANTENNA OR CABLE
OR SATELLITE TO THIS UNIT.
the broadcasting in
THEN PRESS CH K,
IN ORDER TO PERFORM
"AUTO PRESET CH ".
your area.
When the scanning is completed, or [MENU] is pressed during channel scanning to cancel it, the
tuner stops on the lowest memorized channel.
Notes:
In case no channel can be received by the channel scanning, "NO TV SIGNALS" is displayed on
●
the screen. Turn off the unit and check the antenna connection, then follow step 1 again.
If those settings do not work properly, please call our help line on the front page of this owner's manual.
●
SELECTING AUDIO/VIDEO INPUT
When you use the AUDIO/VIDEO input jacks, select "VIDEO1" or "VIDEO2" mode by
pressing [INPUT SELECT] on the remote control or [SELECT] on the main unit. The input
mode changes by pressing the button as following:
INPUT
TV channel
SELECT
TILT STAND
Tilt Stand
Adjust the stand to change the angle of TV (-5° ~ 10°).
OPERATIONS
REMOTE CONTROL AND TOP PANEL FUNCTION
IR transmitter
To send infrared ray (IR) signal
POWER button
To turn TV on/off
POWER
VOL
X X
/
Y Y
buttons
m
To adjust volume
VOL
To decide the command of settings
1
4
7
MENU button
MENU
To view on-screen menu
MUTE button
MUTE
To mute sound
DISPLAY button
To display CH No./Audio Status
Note:
You can test if the remote control sends out the infrared signal with an AM radio.
●
(Refer to "TROUBLESHOOTING GUIDE".)
MENU button
To view on-screen menu
VOLUME
To adjust volume
MENU
VOLUME
CHANNEL
Note:
If some digits appear in the corner of the screen when the unit is turned on at the first time,
●
press [POWER] without unplugging the power cord.
2
2
If the TV screen shows
- HELPFUL HINTS -
1. PLEASE CHECK TO SEE IF THE
snow noise and there is
ANTENNA/CABLE/SATELLITE IS
PROPERLY CONNECTED.
2. DID YOU PERFORM "AUTO PRESET CH" ?
no operation for more
3. PLEASE REFER TO FRONT PAGE OF THE
OWNER'S MANUAL OR REAR PANEL FOR
than 5 seconds,
SUPPORT LINE INFORMATION.
"HELPFUL HINTS"
appears. Follow the
instructions listed on-
screen.
VIDEO1
VIDEO2
-5° 10°
INPUT SELECT button
INPUT
SELECT
To select TV or external input
CH
K K
/
L L
buttons
o
CH
To select channels and move
p
up/down through menu items
n
Channel number buttons
2
3
Press two digits to directly access the
desired channel. Remember to press
5
6
a "0" before a single digit channel.
+100 button
8
9
Press to select cable channels
higher than 99.
0
+100
SLEEP button
To set Sleep Timer
SLEEP
CH RET
DISPLAY
CH RET button
To return to previous channel
X X
/
Y Y
buttons
CHANNEL
K K
/
L L
buttons
To select channels
SELECT button
To select TV or external input
POWER button
To turn TV on/off
SELECT
POWER
Infrared Sensor Window
Publicidad
