Publicidad
Idiomas disponibles
Idiomas disponibles
• KEEP CHILDREN AWAY – All visitors should be kept at a safe distance from
work area.
• STORE IDLE UNIT INDOORS - When not in use, the unit should be stored in-
doors in a dry location – out of reach of children.
• DON'T FORCE THE TOOL – It will do the job better and with less likelihood of a
risk of injury at the rate for which it was designed.
• USE RIGHT TOOL – Do not use the tool for any job except that for which it is
intended.
ELECTRICAL SAFETY WARNINGS AND INFORMATION
• This tool is double-insulated – repair or replace damaged cords.
• Since this tool is double-insulated, a two wire extension cord (an extension cord
without a ground) may be used. A three-wire extension cord (an extension cord
with a ground) that uses a NEMA type connector (parallel blade, U ground) is
recommended. Use only round-jacketed extension cords approved for outdoor
use.
• To reduce risk of electric shock, this unit has a polarized plug (one blade is wider
than the other). This unit will fit with a polarized plug only one way. If the exten-
sion cord plug will not completely fit on the units plug, reverse the plug. If the ex-
tension cord will still not fit, use an extension cord with the proper polarized con-
nection. Do not alter the unit's plug or extension cord in any way.
• A nameplate on the unit will indicate the voltage used. This information is
needed to determine the wire size (AWG) of the extension cord you should use.
Never connect the unit to an AC voltage that differs from this voltage.
• WARNING: To reduce the risk of electric shock, use the unit only with an exten-
sion cord intended for outdoor use, such as SW-A, STW-A, STOW-A, SJW-A,
SJOW-A, SJTW-A, or SJTOW-A cord types.
MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR 120 VOLT APPLIANCES
USING 0-12 AMPS
Cord length
25
*Wire Size (AWG)
16
*The wire size (AWG) for 120-Volt appliances using 12-16 amps is 14 AWG for 25
feet, 12 AWG for 50 feet, and NOT RECCOMENDED for 100 or 150 feet.
• GROUND FAULT CIRCUIT INTERRUPTER (GFCI) PROTECTION should be
provided on the circuits(s) or outlet(s) to be used for the hedge trimmer. Use re-
ceptacles with built-in GFCI protection for an extra measure of safety.
• CORD SETS: Make sure the cord on the unit and the extension cord are in good
condition. The extension cord should be heavy enough to carry the current the
unit will draw. An undersized cord will cause a drop in line voltage that will cause
the unit to loose power and overheat. The above table shows the correct exten-
sion cord size based on the cord length and nameplate ampere rating. If you are
not sure what cord size to use, use the next heavier size. The smaller the gauge
number, the heavier the cord.
•
DO NOT ABUSE THE CORD – Never carry the unit by its cord or pull on it to
disconnect it from the receptacle. Keep the cord away from heat, oil, and sharp
edges and corners.
50
100
150
16
16
14
3
• Routinely inspect the unit's cord as well as the extension cord used. Look for
cuts, nicks, or cracks in the cord's insulation. Also inspect the connectors to see
if they are bent or broken. Repair or replace cords if any defects appear.
OPERATIONAL SAFETY WARNINGS
• DANGER: KEEP HANDS AND ALL BODY PARTS AWAY from the blades. The
edges are sharp and can cause injury even when the tool is OFF.
• CAUTION: Blades coast after the unit is turned off.
• DRESS PROPERLY – Do not wear loose clothing or jewelry. They can be caught
in moving parts. Use of gloves and substantial hard toed footwear is recom-
mended when working outdoors. Wear protective hair covering to contain long
hair.
• DON'T OVERREACH – Maintain proper footing and balance at all times. Use
both hands to operate unit safely.
• USE SAFETY GLASSES – Always wear proper eye protection and use a face or
dust mask if operation is dusty.
• MAINTAIN UNIT WITH CARE – Keep the unit clean for best performance and to
reduce the risk of injury. Follow instructions for service. Keep handles dry, clean,
and free from oil and grease.
• UNINTENTIONAL STARTING – Don't hold the switch area while carrying the unit
while it is plugged in. This may cause it to start inadvertently if not handled prop-
erly. Be sure the switch is in the off position when plugging in the unit.
• CHECK DAMAGED PARTS – If the unit experiences a hard impact, check that
no parts were damaged and verify that the unit operates properly. Check for mis-
alignment or bending of moving parts, breakage of parts, and any other condition
that may affect operation. A part that is damaged should be properly repaired or
replaced by an authorized service center.
• STAY ALERT – Pay attention to what you are doing and the position of the unit's
blade. Use common sense. Do not operate the tool when you are tired.
• DON'T GRASP THE EXPOSED CUTTING BLADES or cutting edges when pick-
ing up or holding the unit. Do not attempt to remove cut material nor hold material
to be cut when blades are moving. Make sure the unit's switch is off when clear-
ing jammed material from blades.
• USE BOTH HANDS TO OPERATE THE UNIT. Keep one hand on the trigger
housing and the other on the front accessory handle. NEVER use the unit's
guard as a handle.
• STOP THE MOTOR WHEN THE UNIT BECOMES ENTANGLED WITH A FOR-
EIGN OBJECT. Inspect for damage. Do not operate with loose or damaged
parts.
• UNPLUG UNIT – while cleaning or clearing blades of debris and during other
maintenance or repair.
• KEEP INSTRUCTIONS AND REFER TO THEM OFTEN. If you loan this tool to
someone please also loan them these instructions so they may safely understand
how to use this unit.
SAVE THESE INSTRUCTIONS
4
Publicidad
