Rockford Fosgate PUNCH P400-1 Instalación Y Funcionamiento página 10

T
ROUBLESHOOTING
Procedure 5: Check Amplifier if you experience excess Engine Noise.
1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.
OR
2. Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo
directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.
OR
3. Remove existing ground wires for all electrical components. Reground wires to different locations.
Verify that grounding location is clean, shiny metal free of paint, rust etc.
OR
4. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of
vehicle.
OR
5. Have alternator and battery load tested by your mechanic.Verify good working order of vehicle
electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.
S
PECIFICATIONS
MODEL- PUNCH
Continuous Power Rating (RMS) - Measured at 14.4 Battery Volts
4 Load Mono
2 Load Mono
1 Load Mono
Dimensions: Height
Width
Length
External Battery Fuse Rating
"A" Weighted Signal to Noise Ratio
Referenced to 1 Watt into 4 ohms
"A" Weighted Signal to Noise Ratio
Referenced to rated output into 4 ohms
Crossover Slope
Crossover Frequency (P300-1/P400-1)
Crossover Frequency (P500-1bd/P700-1bd/P1000-1bd)
Frequency Response (P300-1/P400-1)
Frequency Response (P500-1bd/P700-1bd/P1000-1bd)
Signal Voltage Adjustment Range
Protection
Equalization PEQ (Punch Equalization)
Input Impedance
Infrasonic Filter (P500-1bd/P700-1bd/P1000-1bd)
Operating Voltage
Balanced Inputs
CMRR (Common Mode Rejection Ratio)
Damping Factor
THD+N (Total Harmonic Distortion+Noise)(P300-1/P400-1)
THD+N (Total Harmonic Distortion+Noise)(P500-1bd/P700-1bd/P1000-1bd) < 0.8% @ 1 ohm
These specifications are Amplifier Power Standard CEA-2006 Compliant
Specifications subject to change without notice
10
All manuals and user guides at all-guides.com
P300-1 P400-1
150 Watts x 1 200 Watts x 1
300 Watts x 1 400 Watts x 1
–
2.25" (5.71cm) 2.25" (5.71cm)
7.625" (19.37cm) 7.625" (19.37cm) 7.625" (19.37cm) 7.625" (19.37cm) 7.625" (19.37cm)
9.0" (22.80cm) 9.0" (22.80cm) 10.25" (26.03cm) 10.25" (26.03cm) 14.375" (36.50cm)
60A 60A
Thermal switch shuts down the amplifier in case of overheating.
P500-1bd P700-1bd
200 Watts x 1 225 Watts x 1
400 Watts x 1 450 Watts x 1
– 500 Watts x 1 700 Watts x 1
2.25" (5.71cm) 2.25" (5.71cm)
100A
≥80 dB
≥100 dB
12dB/octave Butterworth
variable from 50Hz to 500Hz
variable from 35Hz to 250Hz
20Hz to 20kHz ±1.0dB
20Hz to 250Hz ±1.0dB
Variable from 150mV to 4V (RCA Input)
Short circuit protection shut downs the amplifier in
case of very low impedance or shorted speaker wires.
Variable from 0dB to +18dB @ 45Hz and/or
0dB to +12dB @ 12kHz (P300-1/P400-1)
20K ohms
On/Off Selectable 12dB/Octave, -3dB @ 28Hz
9 to 16 Volts DC
Yes
>55dB @ 1kHz
>200
< 0.1% @ 2 ohm
P1000-1bd
250 Watts x 1
500 Watts x 1
1000 Watts x 1
2.25" (5.71cm)
100A 140A