Publicidad
Idiomas disponibles
Idiomas disponibles
Save all warnings and instructions for
future reference.
1. Be familiar with the controls and proper use of the
equipment.
2. Cutting elements continue to rotate after the
motor is switched off.
3. Never allow children or people unfamiliar with the
instructions to use the machine.
4. Stop using the machine while people, especially
children, or pets are nearby.
5. Only use the machine in daylight or good artificial
light.
6. Before using the machine and after any impact,
check for signs of wear or damage and repair as
necessary.
7. Take care against injury from any device fitted for
trimming the filament line length. After extending
new cutter line always return the machine to its
normal operating position before switching on.
8. Never fit metal cutting elements.
9. This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety. Children should be supervised to ensure
that they do not play with the appliance.
10. Use the tool with the utmost care and attention.
11. Operate the tool only if you are in good physical
condition. Perform all work calmly and carefully.
Use common sense and keep in mind that the
operator or user is responsible for accidents or
hazards occurring to other people or their
property.
12. Never operate the tool when tired, feeling ill or
under the influence of alcohol or drugs.
13. The tool should be switched off immediately if it
shows any signs of unusual operation.
Intended use of the tool
1. Use right tool. The cordless string trimmer is only
intended for cutting grass, light weeds. It should
not be used for any other purpose such as hedge
cutting as this may cause injury.
Personal protective equipment (Fig. 1 & 2)
1. Dress Properly. The clothing worn should be
functional and appropriate, i.e. it should be tight-
fitting but not cause hindrance. Do not wear either
jewelry or clothing which could become entangled
with high grass. Wear protective hair covering to
contain long hair.
2. When using the tool, always wear sturdy shoes
with a non-slip sole. This protects against injuries
and ensures a good footing.
3. Wear protective glasses or goggles.
Electrical and battery safety
1. Avoid dangerous environment. Don't use the tool
in damp or wet locations or expose it to rain.
Water entering the tool will increase the risk of
electric shock.
All manuals and user guides at all-guides.com
2. Recharge only with the charger specified by the
3. Use power tools only with specifically designated
4. Do not dispose of the battery(ies) in a fire. The cell
5. Do not open or mutilate the battery(ies). Released
Starting up the tool (Fig. 3)
1. Make sure that there are no children or other
2. Before use always check that the tool is safe for
3. Check damaged parts before further use of the
4. Switch on the motor only when hands and feet are
5. Before starting make sure that the cutting tool has
Method of operation
1. Never operate the machine with damaged guards
2. Only use the tool in good light and visibility.
3. Take care against injury to feet and hands from
4. Keep hands and feet away from the cutting means
5. Never cut above waist height.
6. Never stand on a ladder and run the tool.
7. Never work on unstable surfaces.
8. Don't overreach. Keep proper footing and balance
9. Remove sand, stones, nails etc. found within the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
battery packs. Use of any other battery packs may
create a risk of injury and fire.
may explode. Check with local codes for possible
special disposal instructions.
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.
people within a working range of 15 meters (50 ft),
also pay attention to any animals in the working
vicinity. Otherwise stop using the tool.
operation. Check the security of the cutting tool
and the guard and the switch trigger/lever for easy
and proper action. Check for clean and dry
handles and test the on/off function of the switch.
tool. A guard or other part that is damaged should
be carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other condition that may affect
its operation. A guard or other part that is
damaged should be properly repaired or replaced
by our authorized service center unless indicated
elsewhere in this manual.
away from the cutting tool.
no contact with hard objects such as branches,
stones etc. as the cutting tool will revolve when
starting.
or without the guards in place.
During the winter season beware of slippery or
wet areas, ice and snow (risk of slipping). Always
ensure a safe footing.
the cutting tool.
at all times and especially when switching on the
motor.
at all times.
working range. Foreign particles may damage the
cutting tool and can cause to be thrown away,
resulting in a serious injury.
7
Publicidad
