Masterpro BGMP-9006 Manual De Instrucciones página 2

EN
FEATURES
BLENDER COMPONENTS
A. Assembled jug
B. Main body
C. Speed control knob
D. Inner cap
E. Jug cover
F. Jug
G. Ring
H. Blender blades
I. Jug base
TECHNICAL INFORMATION
Voltage / frequency: 220-240V 50/60Hz(500W)
Glass jar capacity: 1.5L
IMPORTANT SAFEGUARDS
When using electrical appliance,basic safety precaution should always be followed including the
following:
1.Read all instructions before using.
2.To protect against risk of electrical shock do not put the unit in water or other liquid.
3.Close supervision is necessary when any appliance is used by near children.
4.Unplug from outlet not in use,before putting on or taking off parts,and before cleaning.
5.Avoid contacting moving parts.
6.To reduce the risk of electric shock,this plug will be fit in a outlet only one way.If the plug does not
fit fully in the outlet,reverse the plug.If it still does not fit,contact a qualified electrician.Do not
modify the plug in any way.
7.Do not operate any appliance with a damaged cord or plug,or after the appliance malfunctions,or
is dropped or damaged in any manner.Return appliance to the nearest authorized service facility
for examination,repair or mechanical adjustment.
8.The use of attachments,including canning jars,not recommended by the manufacturer may cause
a risk of injury to persons.
9.Do not use outdoors.
10.Do not let cord hang over edge of a table or counter.
11.Keep hands and utensils out of container while blending to reduce the risk of severe injury to
persons or damage to the blender.A scraper may be used but must be used only when the
blender is not running.
12.Blades are sharp.Handle carefully.
13.To reduce the risk of injury,never place cutter-assembly blades on base without jar properly
attached.
14.Be certain cover is securely locked in place before operating appliance.
All manuals and user guides at all-guides.com
01
15.Always operate blender with cover in place.
16.When blending hot liquids,remove center piece of two-piece cover.
17.Don't switch on the appliance without any food or water.
18.Do not use appliance for other than intended use.
19.The use of attachments or accessories not included with the product are not recommended for
use as they may cause personal or property hazards or injuries.
20.This product is intended for normal domestic/household use only.
21.Cutting blades are very sharp.Handle all parts with extreme care and caution.
22.NOTE:Maximum operating time for the blender is 3 minutes.
WARNINGS:
1. This appliance is not intended for longtime operation.
2. This appliance must not operate when there's nothing in the jar.
3. Do not touch the blade when appliance in service.
4. a. This appliance shall not be used by children.Keep the appliance and its cord out of reach of
children.
b. Appliances can be used by persons with reduced physical,sensory or mental capabilities or lack
of experience and knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and if they understand the hazards involved.
c. Children shall not play with the appliance.
5. The appliance should be repaired by qualified professionals.
6. Swich off the appliance and disconnect from supply before changing accessories or approaching
parts that move in use.
7. a. Always disconnect the appliance from the supply if it is left unattended and before
assembling,disassembling or cleaning.
b. Care shall be taken when handling the sharp cutting blades,emptying the bowl and during
cleaning.
SAVE THESE INSTRUCTIONS
BEFORE FIRST USE
• All parts of the blender are to be thoroughly cleaned before being used for the first time.(see
Section:Cleaning).
• Take out the required length of cable from the cable tidy on the base of the blender and connect
the device to the mains supply.
ASSEMBLY OF THE GLASS JAR
Put the rubber sealing ring (4) on the inner edge of the blade unit (5).
1. Put the rubber sealing (4) on the inner edge of the blade unit (5).
2. Put the blade unit with sealing ring and ring (10) into the cup base (6).
3. Mount the glass jar (3) onto the cup base unit and tune the cup base unit, and tune the cup base
unit in clockwise direction unit it is fixed.
4. Mount the cup with cup unit onto the base unit.
5. After putting the ingredients in the cup,fix the lid (2) onto the cup by pressing down.
6. Insert the inner cover (1) into the opening of the lid,and tune it in anticlockwise directon unit it is
locked.
7. Put the blade unit with sealing ring into the cup base (6).
8. Mount the glass jar (3) onto the cup base unit and tune the cup base unit, and tune the cup base
unit in clockwise direction unit it is fixed.
02
EN