Publicidad
Idiomas disponibles
Idiomas disponibles
charge a partially used pack whenever you desire with
no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface.
If wall mounting, locate the charger within reach of
an electrical outlet, and away from a corner or other
obstructions which may impede air flow. Use the back
of the charger as a template for the location of the
mounting screws on the wall. Mount the charger securely
using drywall screws (purchased separately) at least 1"
(25.4 mm) long, with a screw head diameter of 0.28–0.35"
(7–9 mm), screwed into wood to an optimal depth leaving
approximately 7/32" (5.5 mm) of the screw exposed. Align
the slots on the back of the charger with the exposed
screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can
be stored on CRAFTSMAN VersaTrack™ Trackwall.
Hooks and accessories are sold separately. Please
refer to the VersaTrack™ Trackwall accessory sheet for
further information.
nOTE: The CMCB101 charger is not CRAFTSMAN
VersaTrack™ Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Intended Use
Your small angle grinder has been designed for household
use for grinding, sanding, and wire brush applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Attaching the Auxiliary Handle (Fig. A)
WARNING: This handle SHOULD BE USED AT ALL
TIMES to maintain complete control of the tool.
Always make sure the handle is tight.
Screw the auxiliary handle
threaded mounting holes of the gear case.
Guards
CAUTION: Guards must be used with all grinding
wheels, sanding flap discs, wire brushes, and
wire wheels. The tool may be used without a guard
only when sanding with conventional sanding discs.
Refer to Figure A to see guards provided with the
unit. Some applications may require purchasing the
correct guard from your local dealer or authorized
service center.
nOTE: Edge grinding and cutting can be performed with
Type 27 wheels designed and specified for this purpose;
0.25" (6.35 mm) thick wheels are designed for surface
grinding while thinner Type 27 wheels need to be examined
for the manufacturer's label to see if they can be used for
surface grinding or only edge grinding/cutting.
nOTE: See the Accessories Chart to select the proper
guard / accessory combination.
Mounting and Removing Guard (Type 27)
Mounting guard (Fig. B)
1. Open the guard latch lever
the gear case
21
with the arrow
2. Push the guard down until the guard lugs
and rotate freely in the groove on the gear case hub.
3. With the guard latch open, rotate the guard into the
desired working position. The guard body should be
positioned between the spindle and the operator to
provide maximum operator protection.
4. Close the guard latch to secure the guard on the gear
case cover. You should not be able to rotate the guard
by hand when the latch is closed. Do not operate
the grinder with a loose guard or the clamp lever in
open position.
English
7
tightly into one of the
9
, and align the arrow on
22
on the guard.
13
engage
9
Publicidad
