Publicidad
Idiomas disponibles
Idiomas disponibles
Charger safety warnings
– This appliance is not designed for use by other people (children
included), physical, sensory or mental incapability or lack of ex-
perience and knowledge of whose prevent from safe use of the
appliance without being supervised, or without being instructed
on use of the appliance by a person responsible for their safety.
– Children should be supervised to avoid their playing with the ap-
pliance.
Information about noise level
and vibrations
The values have been measured in conformity with EN 60745-1.
CBU 125
Acoustic pressure level L
= 85.1 dB (A).
pA
Acoustic power level L
= 96.1 dB (A).
wA
In accuracy of measurements K = 3.0 dB (A).
ATTENTION! Noise is generated during work!
Use ear protection!
The weighted value of vibrations affecting hands and arms
a
= 1.84 m.s
.
-2
h
In accuracy of measurements K = 1.5 m.s
The emission values specified (vibration, noise) were measured in ac-
cordance with the test conditions stipulated in EN 62481 and are intend-
ed for machine comparisons. They are also used for making preliminary
estimates regarding vibration and noise loads during operation.
The emission values specified refer to the main applications for which
the power tool is used. If the electric power tool is used for other ap-
plications, with other tools or is not maintained sufficiently prior to
operation, however, the vibration and noise load may be higher when
the tool is used.
Take into account any machine idling times and downtimes to estimate
these values more accurately for a specified time period. This may signif-
icantly reduce the load during the machine operating period.
Use
The machine is designed for cutting, roughing and brushing metal and
construction materials without the use of water. When cutting construc-
tion material, ensure sufficient dust extraction and always clean the ma-
chine after work (cleaning with compressed air recommended).
The user bears full responsibility for the consequences of using the ma-
chine for purposes it was not designed for.
Accumulator Charging Instructions
1. Please make sure the mains voltage is the same as the voltage list-
ed on the charger's machine plate. Connect the charger (N1) to a
power source. A red LED indicator (N2) will light up. This means the
charger is ready to charge. If the red LED indicator does not light up,
check the connection to power supply. If the power supply func-
tioning correctly, bring the charger in for repair to an authorised
service centre!
2. Slide the accumulator (B1) all the way into the charger.
3. The red LED will light up and the green LED (N2) will start flashing
to indicate that the accumulator is charging.
4. After approximately 60 minutes, the accumulator should be fully
charged, indicated by the green and red LED staying lit without
flashing.
5. Remove the accumulator from the charger. If you do not wish to
charge another accumulator, disconnect the charger from the pow-
er source.
Overview of LED charging indicator signals (N2):
Green LED
Red LED
off
on
flashing
on
on
on
off
flashing
alternately flashing
-2
.
Meaning
connected to a power source
accumulator is charging
accumulator is charged
charger or battery temperature
too high
accumulator is damaged
New batteries:
Battery capacity may be slightly smaller than the listed value during the
first few initial charge cycles. The reason is that the chemical composi-
tion of the batteries has not been activated yet. This is a temporary issue
and will resolve on its own after a few charge cycles.
Note:
• A blinking green indicator means that the battery is fully charged or
that it is in slow charge mode, which maintains a low charge level of
the battery.
• The initial battery charge may take longer then 60 minutes (accord-
ing to battery capacity) depending on the environment tempera-
ture, the power supply and the current charge level.
• If you are not using the charger, please unplug it from the power
source.
Important information about the charging
process:
1. To get the best out of the batteries in terms of longevity and per-
formance is to charge them at an ambient temperature of 18 °C
to 24 °C. DO NOT CHARGE the batteries at temperatures below
0 °C and above 45 °C. This is very important. You will prevent serious
battery damage.
• Do not charge the batteries in direct sunlight, especially in the sum-
mer! You will prevent extreme overheating, which could damage
them!
2. If a battery that is too cold (below 0 °C) is inserted into the charg-
er, the charger will not begin charging it right away; instead, the
green and the red indicator light will begin blinking. Once the bat-
tery reaches the right temperature naturally (within the standard
range), the fast charge process will begin automatically.
• If a battery that is too hot (more than 45 °C), is inserted into the
charger, the charger will not begin charging it right away; instead,
the green and the red indicator light will begin blinking. Once the
battery reaches the right temperature (within the standard range),
the fast charge process will begin automatically.
3. If it is not possible to charge the batteries properly (the red indica-
tor is blinking):
• Check that the battery contact surfaces are not dirty. Clean them
with a cotton wad and alcohol as needed.
• If the battery is still not charging properly, send or bring the charger
(including the batteries) to your nearest authorised service centre.
4. Under certain conditions and if the charger is connected to power,
foreign material may short circuit the charge contacts inside the
charger. Foreign conducting substances, such as steel fibres, alumini-
um foils or metal deposits must be removed from the charger contin-
uously. Always unplug the charger from power prior to cleaning.
5. If you are carrying out several different charge operations one after
the other, the charger may become hot. This is normal and is not
a sign of a technical problem.
6. Prevent liquid from getting inside the charger as it could cause an
electrical injury. Do not place the battery in a hot environment if
you wish to facilitate the battery cool down process.
7. Accumulator batteries can remain plugged into the charger with-
out a risk of damage to them or the charger itself. The batteries
will remain fully charged in the charger. DO NOT LEAVE charged
batteries in the charger if the charger is not plugged into the power
outlet.
8. DO NOT USE ACCUMULATOR BATTERIES if they are damaged or if
liquid leaks out of the cells. If the battery liquid comes into contact
with your skin, immediately flush the area with water and monitor
the skin's reaction. Seek medical attention if needed. If it comes into
contact with your eyes, flush them with lots of water and immedi-
ately seek medical attention.
9. If you are charging a fully discharged battery or if you stop charging
the battery before it is fully charged, you must count each of these
cycles as an entire charging cycle.
Note on Lithium-ion (Li-Ion) batteries
• These types of batteries do not have a memory effect, in other
words, the batteries can be charged at any state of discharge. If you
take the batteries out of the charger prior to fully charging them, it
will not damage them.
• Each Li-Ion battery is equipped with deep discharge protection. If
the voltage falls (due to overloading or discharge) below the mon-
itored range, the electronic circuit will disconnect the cells. The
machine will then either work intermittently or not at all. You must
reduce machine load or recharge the battery.
English
21
Publicidad
