Narex CBU 125 Instrucciones De Uso página 23

Checking Accumulator Status
The machine is fitted with an accumulator status control panel (B3).
Press the control button (B4) on the accumulator status panel (B3). An
accumulator status indicator (B5) will light up based on the state of
charge (capacity) of the accumulator.
Overview of the state of charge (capacity) indication of the accumulator:
Number of fully lit LEDs
3
2
1
Maintenance and Service
Remove the accumulator before transport, storage or be-
fore doing any work on the power tool (e.g. maintenance,
change of tools). Risk of injury in the event of accidentally
pressing the switch.
Always keep the power tool and its vents (13) clean. Clean it reg-
ularly, particularly during work that generates a large amount
of dust. After extensive use, let the power tool run at no load for
a while to let it cool down.
Warning regarding optimal handling of the accumulator. Protect the
accumulator from humidity and water. Only store the accumulator at
temperatures between -20 °C and +50 °C. For instance, you should not
store the accumulator in a car in the summer. Occasionally clean the
accumulator vents with a soft, clean, dry brush. A significantly reduced
runtime after recharging indicates that the accumulator is worn down
and needs replacing.
Attention! With regard to the principles of protection
against injury by electric current and the protection rating
of the device, all maintenance and service work that re-
quires the removal of the machine's casing must be done only by
an authorised service centre!
You can find an up-to-date list of authorised service centres on our web-
site at www.narex.cz in the "Service Points" section.
Accessories
The accessories recommended for use with this device are available
commercially in the shops with hand el. tools.
Storage
Packed appliance may be stored in dry, unheated storage place with
temperature not lower than -5 °C.
Unpacked appliance should be stored only in dry storage place with
temperature not lower than +5 °C with exclusion of all sudden temper-
ature changes.
Environmental protection
Power tools, accessories and packaging should be sorted for environ-
mental-friendly recy.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, power
tools that are no longer suitable for must be separately collected and
sent for recovery in an environmental-friendly manner.
State of charge
100 %
less than 60 %
less than 30 %
Warranty
Our equipment is under warranty for at least 12 months with regard to
material or production faults in accordance with national legislation. In
the EU countries, the warranty period for exclusively private use is 24
months (an invoice or delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and tear, overloading,
improper handling, or caused by the user or other damage caused by
not following the operating instructions, or any fault acknowledged at
the time of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has not been
dismantled before being sent back to the suppliers or to an authorised
NAREX customer support workshop. Store the operating instructions,
safety notes, spare parts list and proof of purchase in a safe place. In
addition, the manufacturer's current warranty conditions apply.
Note
Due to continuous research and development work, we reserve the
right to make changes to the technical content of this documentation.
Certificate of Conformity
CBU 125:
We declare that the device meets requirements of the following stand-
ards and directives.
Safety:
EN 60745-1: 2009+A11: 2010
EN 60745-2-3: 2011/A13: 2015
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014-1: 2017
EN 55014-2: 2015
Directive 2014/30/EU
RoHS:
Directive 2011/65/EU
Place of storage of the technical documentation:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa, Czech Republic
2021
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
English
Jaroslav Hybner
CEO of the company
Marec 1, 2021
23