Manuales relacionados para Truper SOIN-130M
Resumen de contenidos para Truper SOIN-130M
- Página 1 Manual Mini 40 % Inverter Welder Work Cycle Applies for: Code Model 102322 SOIN-130M SOIN-130M Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Contents CAUTION Technical specifications Power Requirements To gain the best performance of the tool, prolong the duty life, General Power Tools Safety Warnings make the Warranty valid if necessary, and to avoid hazards Safety Warnings for Inverter Welders of fatal injuries please read and understand this Manual before Parts using the tool.
- Página 3 Technical specifications SOIN-130M Code 102322 Description Inverter Welder Input Power 127 V Frequency 50 Hz / 60 Hz Current 39 A No. of Phases 1 phase Output Input Rated Capacity 4.9 kVA Open Circuit Voltage 69 V c.c. Current Range...
- Página 4 General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 5 Safety Warnings for Inverter Welders Protection Equipment for Welding Prevent Injuries and Accidents WARNING WARNING • Wear a welding mask to protect eyes • Risks of electric shock: and face when soldering. Assure the mask protective glass An electric shock coming from the soldering electrode may shade is adequate for the soldering process to carry out.
- Página 6 Parts Thermal Protection Light light Work Piece Grounding Clamp Power Adjustment Control Strap Negative Slots Connection ( - ) Positive Connection ( + ) Switch Power Cord Electrode Holder Ventilation Slots Carrying Ventilation Strap Inlet Hammer-Brush for Slag Removal Protective To get better results use Mask cable set with...
- Página 7 Installation Connections CAUTION To prevent electric shock please consult information in the “Electrical Requirements” section in pages 3 and 5. • The fast connections in the electrode holder and the grounding clamp are inserted and turned one quarter of a turn in a clockwise direction in the outlets found iin the front panel to be secured.
- Página 8 Start Up Preparation • Only experience, practice and care can guarantee a good welding job. • The factor intervening in the welding process are many: required current, distance between the electrode and the 45° 45° work piece, soldering speed and direction, thickness and type of the material, the work piece position, electrode angle and also gauge, type of material and electrode covering.
- Página 9 Start Up Examples of welding Correctly Applied Welding Electrode movement too fast and / or very low current. Electrode movement too slow and / or very high current. Electrode too separated from the work piece. Spiral movement. Half-Moon movement. Bevel Zigzag Movement.
- Página 10 Maintenance • The correct use and regular cleansing extend the useful life of the welder. CAUTION • Only qualified personnel shall carry out repairs. We recommend visiting a Authorized Service Center to repair your welder, get supplies or accessories. Regular Maintenance Storage •...
- Página 11 Troubleshooting Problem Cause Solution The thermal protection • The welder has no adequate ventilation. • Keep the welder least 11.8” away from any walls at to light is ON. allow air circulation. • Environment temperature is too high. • The welder will recuperate once the temperature gets back to the right range to operate.
- Página 12 Notes ENGLISH...
- Página 13 In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS...
- Página 14 . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.