Descargar Imprimir esta página

Husqvarna CS 2238 Manual De Instrucciones página 21

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 26
General
The user must only carry out the maintenance and
service work described in this Operator's Manual. More
extensive work must be carried out by an authorised
service workshop.
Carburettor adjustment
Your Jonsered product has been designed and
manufactured to specifications that reduce harmful
exhaust fumes.
Function
The carburettor governs the engine's speed via the
throttle control. Air and fuel are mixed in the
carburettor. The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic settings and running in
The basic carburettor settings are adjusted during
testing at the factory. Fine adjustment should be carried
out by a skilled technician.
Rec. idle speed: See the Technical data section.
Fine adjustment of the idle speed T
Adjust the idle speed with the T-screw. If it is necessary
to re-adjust, turn the T-screw clockwise while the engine
is running, until the chain starts to rotate. Then turn anti-
clockwise until the chain stops. When the idle speed is
correctly adjusted the engine should run smoothly in
every position and the engine speed should be safely
below the speed at which the chain starts to rotate.
WARNING! Contact your servicing
!
dealer, if the idle speed setting cannot
be adjusted so that the chain stops. Do
not use the chain saw until it has been
properly adjusted or repaired.
5451868-53 Rev. 2 2008-12-19
MAINTENANCE
Checking, maintaining and
servicing chain saw safety
equipment
Note! All service and repair work on the machine
demands special training. This is especially true of the
machine's safety equipment. If your machine fails any
of the checks described below we recommend that
you take it to your service workshop. Any
maintenance other than that described in this manual
must be carried out by your servicing dealer (retailer).
Switch off the engine and take off the ignition cable
before repairs or maintenance
Chain brake and front hand guard
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum. Dirt and wear can impair
operation of the brake. (45)
Regularly check that the brake band is at least 0.6 mm
thick at its thinnest point.
Checking the front hand guard
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to
the clutch cover. (46)
Checking the inertia brake release
Place the chain saw, with the engine switched off, on a
stump or other stable surface. Release the front handle
and let the saw fall by its own weight, rotating around the
rear handle towards the stump.
When the bar hits the stump the brake should be
applied. (47)
Checking the brake trigger
Place the chain saw on firm ground and start it. Make
sure the chain does not touch the ground or any other
object. See the instructions under the heading Start and
stop.
Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles.
Apply full throttle and activate the chain brake by tilting
your left wrist forward onto the front hand guard. Do not let
go of the front handle. The chain should stop
immediately.
Throttle lockout
Make sure the throttle control is locked at the idle
setting when the throttle lockout is released.
Press the throttle lockout and make sure it returns to
its original position when you release it.
Check that the throttle control and throttle lockout
move freely and that the return springs work properly.
Start the chain saw and apply full throttle. Release
the throttle control and check that the chain stops
and remains stationary. If the chain rotates when the
throttle control is in the idle position you should check
the carburettor idle adjustment.
English – 21

Publicidad

loading