Metabo CS 22-355 Manual Original página 14

en ENGLISH
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Wrench depot
2 Wrench for replacing cutting discs and
adjustment work
3 Cutting depth limiter
4 Transportation lock
5 Lever
6 Cutting disc *
7 Safety cover
8 Spindle locking knob
9 Handle
10 Trigger switch
11 Safety switch (for protection against accidental
start)
12 Spark deflector plate
13 Vice
14 Lever for quick adjustment
15 Crank
16 Stopper
17 Screws (for setting cutting angle and maximum
clamping width)
* not in scope of delivery
6. Commissioning
Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
The machine can be supplied only with the mains
voltage and frequency specified on the type plate.
When, for example, a 120 V machine is supplied
with 230 V of mains voltage, the cutting discs and
the machine can be damaged by surpassing the
max. rpm.
All screws must be screwed tight. Screw the
screw tight with the provided wrench to fasten
the cutting disc and check if all other screws are
also screwed tight.
14
Spark deflector plate (12):
Before commissioning the spark deflector plate, tilt
it to the mark.
7. Use
7.1 Setting cutting depth
For presetting the desired cutting depth, e.g. for
several cuts with the same cutting depth.
Setting the cutting depth limiter (3):
- Free the lock nut.
- Set the hexagon screw for the desired cutting
depth.
- Retighten the lock nut.
7.2 Vice
Clamp the workpiece tightly into the vice (13).
Setting the cutting angle:
- Loosen the two screws (17) on the stopper (16).
- Set the desired cutting angle.
- Retighten the two screws (17).
Configuring the maximum clamping width:
The stopper can be set for 3 positions.
- Additionally, remove the two screws (17).
- Shift the stopper (16) to the rear / middle / forward
position.
- Fasten the stopper (16) again with the two screws
(17).
Clamping the workpiece:
- For quick adjustment, turn the lever (14) forwards
and push the crank (15) towards the workpiece.
- Push the lever (14) backwards and tight turn the
crank (15) clockwise to clamp the workpiece.
7.3 Cutting through a workpiece
Danger of crushing! Do not reach into the area
of the joint when lowering the lever!
• Do not begin cutting until the machine has
reached its maximum rpm.
• Slowly lower the cutting disc onto the workpiece
and conduct the cut with little contact pressure.
• After finishing the job, put the lever into the
starting position.
• After a complete cut, switch off the machine,
allow the motor to come to a complete standstill
and only then prepare the next cutting job. The
removal or insertion of workpieces while the
cutting disc is rotating can lead to injury.
• Do not work with too much contact pressure,
since the cutting disc can otherwise quickly
become worn out, or the machine or workpiece
can be damaged.
7.4 Switching on and off
Switching on: Press and hold safety switch (11),
press the trigger (10).
Switching off: release the trigger switch (10).