Invacare Revato H335 Manual Del Usuario página 4

Invacare® Revato
This product is intended to be used as transfer and support
aid when e.g. sitting down and standing up from a toilet seat.
Intended User
Users are any adults and adolescents with restricted or
limited mobility or limited muscle strength. If used without
an assistant, the users must be able to keep their own
balance.
Indications
• Restricted or limited mobility (e.g. legs and/or hips) or
• having balance issues to stand up or walk due to
transitional or permanent disabilities.
There are no contraindications known when using the
product as intended. For the maximum user weight, see 8
Technical Data, page 6 .
3.2 Scope of Delivery
Not all products, models or accessories / options may
be available in every country.
Overview — Complete Products
H335
Foldable grab bar (700 mm)
R7762
Foldable grab bar (500 – 1000 mm)
H345
Foldable grab bar with support leg (700 mm)
R7772
Foldable grab bar with support leg (600 –
1000 mm)
R7780
Foldable grab bar with support leg, armpad
and paper holder (600 – 1000 mm)
Overview — Accessories / Options
R7763 Floor mounted console
R7765–W
Toilet paper holder
R7766
Armpad
The following items are included in the scope of delivery
depending on the product combination resp. accessory /
option ordered:
Foldable Grab Bar (Fig. 1)
Grab bar (1x)
A C
Guard (1x)
B D
Support Leg (Fig. 2)
Set of screw and nut
A
(2x)
B Hinge piece (1x)
C End cap (1x)
Grab bar (1x)
D
Socket (1x)
E
F Wall hinge (1x)
R7763 – Floor Mounted Console (Fig. 3)
Upright (1x)
A
B Attachment plate (1x)
C Clamp (2x)
4
Wall attachment socket
(pre-mounted to bracket) (1x)
Adjustment plate 2° (1x)
G Fixing screw (1x)
Starlock retainer ring
H
(1x)
I Support leg (1x)
Guide (1x)
J
Protective cap (4x)
K
L Foot assembly (1x)
D Nut, DIN 934, M8 (4x)
E Washer, DIN 125,
Ø 8,4 x Ø 16 (4x)
F Plate, pre-mounted to
upright A (1x)
R7765-W – Toilet Paper Holder (Fig. 4)
Roll holder (1x)
A
Hinge piece (1x)
B
Protective cap (1x)
C
Screw, DIN 912,
D
M5 x 25 (1x)
R7766 – Armpad (Fig. 5)
Armpad, PUR (1x)
A
4 Setup
4.1 Installing Foldable Grab Bar
WARNING!
Risk of Falling!
– Mount only to walls that have a sufficient
load-bearing capacity.
Installing the Foldable Grab Bar (Fig. 1)
1. With the user standing upright, without shoes, measure
the height of the thumb's upper joint. This height
corresponds to the grab bar's highest point A (middle
of grab bar).
2. Insert the 2° adjustment plate D.
3. Mark out the location of the holes on the wall (2 above
and 2 below outside) taking into account the previously
measured height.
4. Remove the 2° adjustment plate.
5. Position the wall attachment socket C for the foldable
grab bar accordingly.
6. Drill and insert 4 dowels appropriate for the type of wall.
7. Fix the socket to the wall using suitable screws, washers.
8. Snap the guard B onto the socket.
9. Insert the 2° adjustment plate from below again.
Installing the Support Leg (Fig. 2)
1. Install the front end of the guide J into the oblong hole
in the support leg I using a plastic mallet and starlock
retainer ring H.
2. Remove the lower left-hand fixing screw G from the
socket E.
3. Position the guide J on the outside of the foldable grab
bar, the end with the wall hinge F pointing towards the
support wall or socket E.
4. Fasten the wall hinge F using the socket's lower,
left-hand side fixing screw G.
5. Insert the upper end of the support leg I into the hinge
piece B. Fasten it using the screw and position two
protective caps K.
6. Install the socket's guard.
To decrease the height, turn the foot L
counterclockwise. To increase the height, turn the
foot L clockwise.
Installing the Floor Mounted Console (R7763) (Fig. 3)
This option, when sealed to the floor, enables a
foldable grab bar to be fastened in place when the
wall is unsuitable for this.
1. Position the upright A.
2. The plate F resting on the floor must have its longest
side under the foldable grab bar G.
3. Mark out the location of the 4 screws.
4. Drill and insert 4 dowels appropriate to the type of floor.
E Nut, DIN 934, M5 (1x)
F Protective cap (2x)
G Spacer
Ø 8,2 x Ø 12 x 10 (1x)
H Fastener, Ø 8 (1x)
Glue (1x)
B
1572997-G