Standard Accessories; Applications; Optional Accessories...sOld Separately; Preparation Before Operation - Hitachi Koki C 10FCH2 Instrucciones De Seguridad Y Manual De Instrucciones

ACCESSORIES
WARNING:
Accessories for this power tool are mentioned in this Instruction Manual.
The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

STANDARD ACCESSORIES

1 10 in. (255mm) TCT Saw 2 Dust bag (1 piece)
blade (1 piece) (For wood)
For how to use, refer to
page 14.
(No. of teeth 24
Code No. 318963)

OPTIONAL ACCESSORIES...sold separately

1 Extension Holder and Stopper (Code No. 322710)
2 Saw blade 10 in. (255mm) TCT Saw blade for wood cut (Total teeth: 60)
(Code No. 976472)
3 Saw blade 10 in. (255mm) TCT Saw blade for aluminum cut (Total teeth:
100) (Code No. 319658)
4 Crown molding Vise Ass'y (Code No. 322712) (Include Crown molding
Stopper (L))
5 Crown molding Stopper (L) (Code No. 322713)
6 Crown molding Stopper (R) (Code No. 322714)
NOTE:
Accessories are subject to change without any obligation on the
part of the HITACHI.

APPLICATIONS

Wood and aluminum sash.

PREPARATION BEFORE OPERATION

Make the following preparations before operating the power tool:
1. Remove all packing materials attached or connected to the tool before
attempting to operate it.
2. Installation
16-3/8 in. (416mm)
11/32 in. (9mm)
4 Holes
14-1/6 in. (360mm)
3 Vise Assembly w/knob bolt
(1 piece)
For how to use, refer to
page 11.
6 Sub fence 7 Flat screw
(1 piece) (1 piece)
0 Holder (B) ! Side handle
(1 piece) (1 piece)
4 10mm BOX wrench
(1 piece)
8 M6 Nylon nut
(1 piece)
@ Holder
(1 piece)
Fig. 3
Base
5/16 in. (8mm)
Bolt
Work bench
Attach the power tool to a level, horizontal work bench in accordance with
Fig. 4.
Select 5/16 in. (8mm) diameter bolts suitable in length for the thickness
of the work bench.
Bolt length should be at least 1-3/8 in. (35mm) plus the thickness of the
work bench.
For example, use 2-11/32 in. (60mm) or larger bolts for a 1 in. (25mm)
thick work bench.
The holder attached to the rear of the base helps stabilize the power tool.
Holder (B), clamp lever adjustment:
Attach the included holder (B) in the position as shown in fi gure 5 and
adjust the holder (B) until its bottom surface contacts the work bench
surface. After adjustments, securely tighten the 6mm bolt with the
included 10mm box wrench. Loosen the M6 × 20 screw on the clamp lever
and attach to a position where the clamp lever can be easily operated.
CAUTION:
Attach the power tool to a work bench with bolts (6mm), and if the
turntable has been swiveled 45° degrees or more, be careful not
to let the hand that is holding the side handle get caught between
the side handle and heads of bolts (6mm). Injuries could result.
5 4mm Hex. bar wrench
(Only C10FCH2)
For how to use, refer to
page 10.
9 Plate (A)
(1 piece)
# 6 mm machine screw
(1 piece)
5/16 in. (8mm) Nut
Fig. 4
English
7