Mr. Heater MHU 80 Instrucciones De Uso Y Manual Del Usuario página 7

5. Vent termination must be a minimum of 4' (1.2m) below or
4' (1.2m) horizontally from any soffit vent or under-eave vent.
6. Vent must be a minimum of 6' from an inside corner formed
by two exterior walls. If possible, leave a 10' clearance.
7. Vent termination must be a minimum of 10' (3m) from any
forced air inlet (includes fresh air inlet for other appliances,
such as a dryer).
8. When termination is routed through an exterior combustible
wall the vent must be supported using a listed clearance
thimble. Seal the connection between the single wall and
double wall pipes and the annular space of the double wall
pipe as shown in figure 2. Inside edge of vent termination
tee must be at least 12 inches from outside wall as shown in
figure 3.
9. For horizontal venting, the vent pipe shall be supported with
hangers no more than 3ft. (1m) apart to prevent movement
after installation.
D – HORIZONTAL VENTING – COMMERCIAL
1. Horizontal commercial installations are for buildings which
are not attached to living spaces. The vent may be single wall
vent material installed according to the sections
Venting A - General Recommendations and
Requirements and C - Horizontal Venting General and D -
Horizontal Venting - Commercial. Refer to figure 3.
2. The vent pipe diameter for horizontal commercial installations
shall be 4" (76mm) on 50 units. In all cases, a flue transition
piece (supplied) is required to fit over the outlet of the
induced draft assembly on the appliance.
CATEGORY III VENT ACCORDING TO THESE INSTALLATION INSTRUCTIONS.
INDUCED DRAFT BLOWER
NOTE - MINIMUM HORIZONTAL LENGTH 3 FT. (914MM),
NOT INCLUDING CAP FOR TERMINATION. REFER TO TABLE
2 FOR MAXIMUM LENGTH AND NUMBER OF ELBOWS.
COMMON VENTING NOT ALLOWED WHEN HORIZONTALLY VENTING THE UNIT / UTILITY HEATER
CONDENSATE DRAIN THROUGH TEE PIPE AND DRAIN LOOP
UPWARD SLOPE ON HORIZONTAL VENT-COMMERCIAL INSTALLATION
SLOPE: + 1/4 INCH FOR 1 FOOT RUN MINIMUM.
FLUE TRANSITION
(PROVIDED)
DRAIN LOOP WITH WATER
TRAP (TO CONDENSATE DRAIN)
Compact Unit / Utility Heater
3. Refer to table 2 for maximum vent connector lengths.
4. Select a wall termination point that will maintain ¼" rise per
foot slope of horizontal run of vent pipe.
5. For upward sloped vent a condensate tee and drain must
be installed within the first 5' (1.5m) from the unit heater
to protect the appliance. If a flexible condensate drain line
is used, the drain line must include a loop entering the
structure. If the unit is shut down for an extended period of
time and will be exposed to sub-freezing temperatures, the
condensate may freeze.
E – HORIZONTAL VENTING – RESIDENTIAL
1. For horizontal residential installations these units are
certified as Category III appliances. Venting A - General
Recommendations and Requirements and C - Horizontal
Venting General and E - Horizontal Venting - Residential.
Refer to figure 6.
2. The vent pipe diameter for horizontal residential installations
shall be 4" (100mm) on 50 and 80 units. A standard vent
transition is required at unit in addition to the transition
supplied with the unit.
3. The maximum vent length is 5' (1.5m) plus one 90-degree
elbow. The minimum length is 3'(.91m).
4. The vent must maintain a ¼" rise per foot of slope upwards
toward the termination.
LISTED THIMBLE
THROUGH COMBUSTIBLE
WALL
FIGURE 3
E-7
Operating Instructions and Owner's Manual
12 INCHES MIN.
(30.5 CM)
EXHAUST VENT
TERMINATION TEE
12" (30.5 CM)
MINIMUM ABOVE ALL
HIGHEST SNOWFALL