Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-1702-001.book Page 18 Thursday, February 14, 2013 4:05 PM
18 | English
12 Castor
13 Cable holder
14 Locking latch of filter cover
15 Holder for vacuum tubes
16 Holder for crevice nozzle/elbow
17 Holder for floor nozzle
18 SFC+ switch
19 Tool sleeve
20 SFC+ module
21 Vacuum hose
22 Elbow
23 Disposal bag
24 Flat-fold filter(cellulose)
25 Crevice nozzle
26 Rubber lip
27 Brush insert
28 Floor nozzle
29 Vacuum tube
30 Retainer for vacuum-hose holder
31 Snap-fastener
32 Air diffuser
33 Filter-cleaning actuator
34 Filter cover
35 Level sensors
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Wet/dry vacuum cleaner
Article number
Rated power input
Frequency
Container volume (gross)
Net volume (for fluids)
Dust bag contents
Max. vacuum*
– Vacuum cleaner
– Turbine
Max. flow rate*
– Vacuum cleaner
– Turbine
Max. vacuum capacity
Surface of flat-fold filter
Dust category
Weight according to
EPTA-Procedure 01/2003
Protection class
Degree of protection
Ø
* Measured with a
35 mm and 3 m long vacuum hose
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
1 619 929 L27 | (14.2.13)
Automatic Start/Stop feature*
EU
UK
UK/DK
CH
* Specification of the allowable load of the connected power tool (coun-
try-specific)
Noise Information
Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
GAS 35 L SFC+
3 601 JC3 0..
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
W
1200
Leinfelden, 15.02.2013
Hz
50/60
Assembly
l
35
l
19
Before any work on the vacuum cleaner itself, pull the
l
19
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
230
hPa
hPa
254
– Slide the vacuum-hose holders 4 firmly from above into the
retainers 30 intended for this purpose, until they engage.
36
l/s
Mounting the Vacuum Hose (see figure B)
l/s
74
– Mount the vacuum hose 21 onto the hose connection
W
1380
piece 2 and turn it in clockwise direction to the stop.
2
m
0,615
Note: While vacuuming, an electrostatic charge develops in
L
the vacuum hose and accessories caused through the friction
of the dust, which the operator could experience in the form
kg
12,2
of static discharging (dependent on environmental influences
and physical perception).
/I
As a general rule, Bosch recommends using an anti-static vac-
IP X4
uum hose (accessory), when vacuuming fine dusts and dry
materials.
max. power
Rated voltage
output
220 –240 V
2200 W
110 V
750 W
240/230 V
1800 W
230 V
1100 W
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools
min. power
output
100 W
100 W
100 W
100 W
Publicidad
