Publicidad
Idiomas disponibles
Idiomas disponibles
English
Status
Cardioid preset
.0
.9
.1
Active
Limiter
.8
.2
Signal
.7
.3
Mute/Prot
.4
.6
.5
Ready
e bypassed
Xover [Hz]
Service / User
Fullrange
k
To link a speaker, connect a balanced XLR cable from the "HPF Xover Output" on the subwoofer to the "Input" on
the speaker. Then set the crossover cut-off frequency with the "LPF" knob.
CONNECTING AND LINKING THE RDNET SIGNAL
lay [ms]
tion
System test
USB Data Service
Cardioid preset
0
.0
9
.9
1
.1
Active
8
2
.8
.2
7
3
.7
.3
4
.4
6
.6
Push and Hold to test
5
.5
arity and delay are bypassed
Link
RDNET CONTROL
DESIGNED & DEVELOPED
To enable remote control, connect the "Data Input" of the subwoofer to the hardware interface (RDNet Control
2 or RDNet Control 8) using cables fitted with etherCON connectors. When linking, connect the "Data Output"
of the first subwoofer to the "Data Input" of the second one, and finally from the second subwoofer to the top.
Power up the speakers and make a "GoOnline" request in the AURORA NET software; the "Link" LEDs will confirm
that they are connected.
The "Active" LEDs will start flashing to indicate that there is data traffic. Up to 32 RDNet devices can be daisy-
chained together.
CAUTION!
•
•
VIO S218F
System test
Subwoofer Attenuation
-6
dB
-9
-3
dB
dB
-12
-2
dB
dB
SUBWOOFER
-1
dB
-18
dB
0
-24
dB
dB
Mute
60
70
75
110
80
100
85
90
LPF
HPF
Xover output
SUBWOOFER 1
Status
Subwoofer Attenuation
-6
R R D D N N e e t t
dB
-9
-3
dB
Limiter
dB
-12
-2
dB
Expansion Card
Signal
P P U U S S H H
P P U U S S H H
-1
-18
dB
Remote
Mute/Prot
0
-24
dB
Preset Active
dB
Mute
Ready
Active
Link
Xover [Hz]
Data In
Data Out
60
70
Service / User
Fullrange
75
110
80
85
100
90
LPF
HPF
Xover output
IN ITALY
The cables must be suitably dimensioned, and only qualified personnel may design, install and check
the system. AEB Industriale shall not be held liable if unsuitable or uncertified cables are used, or if
they are not dimensioned correctly for the system and in accordance with the regulations in force in
the country of use
To prevent malfunction or poor sound quality (or data transmission quality for the RDnet
connection), replace any damaged cables.
USB Data Service
Polarity
0°
180°
Push and Hold to test
Balanced
Audio
DESIGNED & DEVELOPED
System test
USB Data Service
dB
dB
Push and Hold to test
VIO S218
VIO S218F
(flyable)
Delay [ms]
0
.0
R R D D N N e e t t
9
.9
1
.1
8
2
.8
.2
Expansion Card
LOUDSPEAKER
P P U U S S H H
P P U U S S H H
7
3
.7
.3
Remote
6
4
.6
.4
Preset Active
5
.5
When green light is on, polarity and delay are bypassed
Active
Link
P P U U S S H H
Data In
Data Out
VIO S218
VIO S218F
(flyable)
Input
Link
IN ITALY
SUBWOOFER 2
R R D D N N e e t t
Expansion Card
P P U U S S H H
Remote
Preset Active
Active
Link
Data In
IN ITALY
DESIGNED & DEVELOPED
Cod. 420120416 REV. 1.0
Status
Cardioid preset
Active
Limiter
Signal
Mute/Prot
Ready
Xover [Hz]
60
Service / User
70
Fullrange
75
110
80
100
85
90
LPF
P P U U S S H H
Data Out
VIO S218
VIO S218F
(flyable)
39
Subw
-12
d
-18
-
X
Publicidad
