Defort DCD-18Nx2D Instrucciones De Servicio página 6

English
Cordless drill/driver
INTENDED USE
• This tool is intended for drilling in wood, metal, ceramic
and plastic; tools with electronic speed control and left/
right rotation are also suitable for screwdriving and thread
cutting
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
5 Switch for selecting mechanical speed
SAFETY
WARNING! Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, fi re and/or seri-
ous injury.
• Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools that
have the switch on invites accidents.
• Recharge only with the charger specifi ed by the manufacturer.
A charger that is suitable for one type of battery pack may
create a risk of fi re when used with another battery pack.
• Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk of
injury and fi re.
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before you
start working
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger (chargers
with a rating of 230V or 240V can also be connected to a
220V supply)
• In case of electrical or mechanical malfunction, immediately
switch off the tool or unplug charger from power source
• SBM Group can assure fl awless functioning of the tool only
when original accessories are used
• Use only accessories with an allowable speed matching at
least the highest no-load speed of the tool
• This tool should not be used by people under the age of 16
years
• Be careful not to drill or drive into areas where electrical
wires may be contacted
• Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories as
well as when carrying or storing the tool
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where temperature
will not exceed 40° C or drop below 0° C
• Batteries will explode in fi re, so do not burn battery for any
reason
• When damaged, and under extreme usage and temperature
conditions, batteries may start to leak
1
2
- if liquid comes into contact with the skin, wash quickly with
soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, fl ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
attention
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc. to
prevent short-circuit
• Do not use charger when damaged; take it to one of the
offi cially registered SBM Group Service Stations for a safety
check
• Do not use battery when damaged; it should be replaced
immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries with
the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire in
the cord of the charger to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of the charger,
it must be disposed of safely and not left unattended
To ensure longer service life and proper performance
of the battery, take the following actions when you
start using new battery:
1. Use the new battery, without recharging it, till its complete
discharge.
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth, prefer-
ably after each use. Keep the ventilation slots free from dust
and dirt.If the dirt does not come off use a soft cloth moistened
with soapy water. Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may damage the plastic
parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please contact
your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during transport,
it is delivered in a sturdy packaging. Most of the packaging ma-
terials can be recycled. Take these materials to the appropri-
ate recycling locations. Take your unwanted machines to your
local SBM Group dealer. Here they will be disposed of in an
environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal site for
chemical waste so that they can be recycled or disposed of in an
environmentally friendly manner.
6