REMS Nano Instrucciones De Servicio página 8

eng
● Check the power cable, extension leads of the power tool and the power
supply regularly for damage. Have these renewed by qualifi ed experts or an
authorised REMS customer service workshop in case of damage.
● Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
Safety Notes for Batteries, Rapid Chargers
WARNING WARNING
Read all the safety notes, instructions, illustrations and technical data which
come with this power tool. Failure to heed the instructions can result in electric
shock, fi re and/or severe injuries.
Keep all safety notes and instructions for the future.
See also www.rems.de → Downloads → Instruction Manuals.
Safety Data Sheets
WARNING WARNING
Read the safety data sheets. Failure to heed the instructions can result in electric
shock, fi re and/or severe injuries.
Keep all safety notes and instructions for the future.
See www.rems.de → Downloads → Safety Data Sheets → Batteries.
Explanation of symbols
WARNING WARNING Danger with a medium degree of risk which could result in death
or severe injury (irreversible) if not heeded.
CAUTION CAUTION
Danger with a low degree of risk which could result in minor injury
(reversible) if not heeded.
NOTICE NOTICE
Material damage, no safety note! No danger of injury.
Read the operating instructions before use
REMS Nano complies with protection class I
REMS Nano 11 V and rapid charger comply
with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il with protection class Il
Not suitable for using outdoors
Environmentally friendly disposal
CE conformity mark
1. Technical Data
Use for the intended purpose
WARNING WARNING
REMS Nano and REMS Nano 11 V are intended for the purpose of cutting pipes.
All other uses are not for the intended purpose and are prohibited.
Guidelines for use of REMS cordless tools, batteries, rapid chargers, power supply
units.
See www.rems.de → Downloads → Instruction Manuals → CUTTING, CHAMFERING,
DEBURRING: OTHER DOCUMENTS
1.1. Scope of Supply
REMS Nano: Electric pipe cutting machine (without cutting wheel),
single open-ended wrench size 8, operating instructions,
carrying case.
REMS Nano 11 V: Cordless pipe cutting machine (without cutting wheel),
Li-Ion battery, rapid charger, single open-ended wrench
size 8, operating instructions, carrying case.
1.2. Article numbers
REMS Nano
REMS Nano 11 V
REMS High-Power-Battery Li-Ion 10.8 V, 2.5 Ah
Rapid-charger 220 – 240 V, 65 W
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules 3B
REMS Herkules Y
REMS Jumbo
REMS Jumbo E
Carrying case
8
System case L-Boxx with inlay
REMS CleanM, Machine cleaner , Machine cleaner , Machine cleaner
1.3. Application Area
REMS Nano, REMS Nano 11 V:
Pipes of pressfi tting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
Operating temperature range
REMS Nano, REMS Nano 11 V
Battery
Rapid charger
1.4. Speed
REMS Nano, REMS Nano 11 V:
Idle speed of cutting wheel
1.5. Electrical Data
REMS Nano:
230 V~; 50 – 60 Hz; 130 W
Fuse (mains) 10 A (B), cut-out operation S3 20 % AB 2/10 min,
radio interference suppressed, protection class I, PE conductor as of
machine no. 3650
REMS Nano 11 V:
10,8 V – ---; 2.5 Ah
Rapid-charger Input
Output 10,8 – 18 V – ---
Input
Output 10,8 – 18 V – ---
1.6. Dimensions
REMS Nano:
L × W × H:
REMS Nano 11 V:
L × W × H:
1.7. Weights
REMS Nano
REMS Nano 11 V drive machine without battery
REMS battery Li-Ion
1.8. Noise Data
Workplace-related emission value
L
wA wA wA
1.9. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.
2. Start-up
2.1. Electrical Connection
WARNING WARNING
Caution: Mains voltage present! Before connecting the electric pipe cutting
machine or the rapid charger, check whether the voltage given on the rating
plate corresponds to the mains voltage. Only use sockets/extension leads with
a functioning protected earth contact for REMS Nano. On building sites, in a
wet environment, indoors and outdoors or under similar installation conditions,
only operate the electric pipe cutting machine on the mains with a fault current
protected switch (FI breaker) which interrupts the power supply as soon as the
leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries
NOTICE NOTICE
844000
Always hold the battery (9) upright when inserting it in the drive unit or the rapid
844001
charger. If inserted at an angle it can cause damage to the contacts and result
844510
in a short circuit which damages the battery.
571560
Total discharging by undervoltage
844050
The Li-Ion batteries may not drop below a minimum voltage because otherwise
844051
the battery could be damaged by "total discharge". The cells of the REMS Li-Ion
120120
battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion batteries
120130
must be charged before use and recharged regularly. Failure to observe this
120200
regulation of the cell manufacturer can lead to damage to the Li-Ion battery by
120240
total discharging.
574436
–10 °C – +60 °C (14 °F – +140 °F)
–10 °C – +60 °C (14 °F – +140 °F)
0 °C – +40 °C (32 °F – +104 °F)
220 – 240 V~; 50 – 60 Hz; 65 W
all-insulated, interference-suppressed
100 – 120 V~; 50 – 60 Hz; 65 W
all-insulated, interference-suppressed
405 × 90 × 103 mm (15.9"× 3.5"× 4.1")
408 × 88 × 105 mm (16.1"× 3.4"× 4.1")
= 78 dB(A) L = 78 dB(A) L = 67 dB(A) L = 67 dB(A) L
pA pA pA pC, peak
1.2 m/s² K = 1.5 m/s²
eng
844045
140119 140119
Ø 12 – 28 mm
Ø 10 – 35 mm
Ø 10 – 40 mm
130 min‫¹־‬
1.9 kg (4.2 lb)
2.0 kg (4.4 lb)
0.2 kg (0.4 lb)
= 87 dB(A) K = 3 dB