Publicidad
Idiomas disponibles
Idiomas disponibles
Description of the Hood
5
1
2
A. Blower and light controls
B. LED lamps
C. Grease filter handle
A
A. Light button
B. Blower button
CFM Reduction System
Before operating your hood:
Some States and Provinces of the US & Canada restrict the
maximum exhausting airflow of range hoods.
Airflow is measured as cubic feet per minute (CFM).
These maximum levels allowed are detailed in the local code
of your area. Please check local codes to find out if you need
to restrict the maximum airflow of your hood. If your local
code mandates a maximum airflow level below the maximum
airflow of this hood (i.e. 400 CFM), please execute the
procedure below to reduce the maximum airflow.
With blower and light turned Off
• Press and hold both buttons at the same time for 3 sec
you will hear a beep and the icon lights (no edge) will
illuminate for 3 seconds.
• This action will disable speed 4 and effectively lower the
maximum airflow to > 300 CFM.
• Locate the CFM certification sticker in the hardware pack.
3
4
D. Grease filter
E. Canopy
F. Duct covers
Control
B
Operating the light
The Light On/Off button (A) controls both lights.
Press once for turning On soft light and the button sun
icon lightens with the bottom half of the edge slightly.
Press again for regular light and the button will be
completely illuminated.
Press a third time to turn Off the light, the whole
button light turns off.
Operating the blower
Press the button (B) to turn On the hood on low
speed, the icon and right low corner of the edge on
button will be illuminated.
Press a second time for medium speed, the icon and
the lower half of the edge on the button enlightens.
Press again to high speed and ¾ of the edge on the
button will illuminate.
Press the button a fourth time to activate Boost
speed for five minutes (the full icon and edge will be
illuminated) and then, automatically switch to high
speed.
Press the button a fifth time to turn Off the blower and
button lights.
Change light color
With lights and motor turned Off, press and hold light button
for 3 sec, both buttons will fully illuminate on the current light
color. The buttons can be used to select desired color (Light
<< button backwards, Blower button forward >>)
Available light colors are white (default color), blue, green or
red. To set color, choose one and press both buttons at the
same time.
Sound
To enter sound mode, with lights and motor turned Off
press both buttons at the same time and the upper left
corner of the light button will illuminate with white light. The
buttons can be used to select desired sound (Light <<button
backwards, Blower button forward>>).
Available feedback sounds are regular beep, soft beep and
mute. As the regular and soft beep are selected, the hood
will reproduce each sound. When mute is selected, upper left
corner of the light button will illuminate with red light. To set
sound, choose one and press both buttons at the same time.
• Peel and Affix this sticker to a visible area in the blower.This
sticker provides official certification to your local inspector
that this hoods maximum airflow has been reduced to >
300 CFM.
Indicators of filter saturation:
At regular time intervals, the hood indicates the need of
performing filter maintenance.
Blower button icon blink (no edge):
Perform grease filter maintenance.
Light button blink (no edge):
Perform activated charcoal filter maintenance.
Reset of filter saturation indicators:
With blower Off press and hold the blower button for 3 sec.
Activation of saturation indicator activated charcoal filter:
NOTE: This operation must be performed with the hood off.
This indicator is normally deactivated; press and hold the
blower button for 3 sec. to activate the function: the button
blinks for 1 sec.
To deactivate the function, press and hold the blower button
for 3 sec., the button blinks for half a sec.
9
Publicidad
