Publicidad
Idiomas disponibles
Idiomas disponibles
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any con-
ductive material.
(2)
Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
(3)
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6.
Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8.
Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. Such conduct may result in a
fire, excessive heat, or explosion.
9.
Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
11.
When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
PARTS DESCRIPTION
► Fig.1
1
Power switch button
4
Oscillation button
7
Battery slot
13. If the tool is not used for a long period of time,
14. During and after use, the battery cartridge may
15. Do not touch the terminal of the tool imme-
16. Do not allow chips, dust, or soil stuck into the
17. Unless the tool supports the use near
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
2.
3.
4.
5.
2
Wind speed change button
5
Wind speed indicator
8
12V DC socket
8 ENGLISH
the battery must be removed from the tool.
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
diately after use as it may get hot enough to
cause burns.
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
CAUTION:
Only use genuine Makita batteries.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
When not using the battery cartridge, remove
it from the tool or the charger.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
3
Auto-off timer button
6
Auto-off timer indicator
9
AC adaptor
Publicidad
