NovoPress ECO203 Instrucciones De Uso página 19

The stated vibration emission value can also be used to obtain an initial estimate of interruptions
during intermittent operation.
Caution The vibration emission value may differ from the stated value while the device is actually in
use, depending upon the manner in which the device is used. It may be necessary to establish safety
measures to protect operating personnel, depending on the actual conditions of use (intermittent
operation.
Pos : 33 /RVT/T echnisc he Daten/Ladeger ät @ 0\mod_1381215657501_18.doc x @ 1310 @ @ 1
Battery charger
For information on the function and operation of the battery charger and the rechargeable batteries,
please consult the battery charger operating instructions.
Pos : 34 /RVT/Kurz bes chr eibung/Pressautomati k/ACO/EC O/202/203 @ 1\mod_1424269079338_18.doc x @ 9192 @ 12 @ 1
7 Brief description of the press device
7.1 Automatic press cycle (Fig. 1)
The device features an automatic press cycle. This ensures that the pressing operation is always
completed. The automatic press cycle is activated after approx. 1.5 seconds. After the automatic press
cycle has been triggered, the green LED (2) goes out and the pressing operation runs automatically.
The pressing operation can then only be stopped by pressing and holding release button (5). After the
pressing operation has been completed, the motor automatically switches off and the green LED (2)
lights up again.
If the start button (1) is released before the automatic press cycle begins, the piston in the press
device moves back to its starting position. The pressing operation will not have been completed. The
pressing operation must be triggered again.
Pos : 35 /RVT/Kurz bes chr eibung/Entlastungs knopf/AC O102, ACO152, AC O/ECO202, AC O202XL @ 0\mod_1382425726244_18.doc x @ 1401 @ 2 @ 1
7.2 Release button (Fig. 1)
The pressing operation can be stopped at any time by pressing and holding the release button (5).
The piston in the press device then returns to its starting position.
Pos : 36 /RVT/Kurz bes chr eibung/Pressstellenbel euc htungACO/EC O203 @ 1\mod_1429080223443_18.doc x @ 11377 @ 2 @ 1
7.3 Pressing point lighting
When the start button (1) is pressed, the pressing point is lit by 2 LEDs (12). If the press device is out
of use for approx. 30 seconds, the device and the LEDs switch off.
Pos : 37 /RVT/Kurz bes chr eibung/Akku allgemei n/Ü bers chrift/AC O/ECO202, AC O/ECO203 @ 0\mod_1382447455193_18.doc x @ 1465 @ 2 @ 1
7.4 Battery (ACO203 only)
Pos : 38 /RVT/Kurz bes chr eibung/Akku allgemei n/Info: nic ht geladen + T emperatur en/AC O102, ACO152, AC O/ECO202, AC O202XL, AF P/EFP202, AXI/AAP102 @ 2\mod_1469431352019_18.doc x @ 21590 @ @ 1
Information!
The batteries are not charged at the factory.
Therefore:
–
Information!
Limited temperature range for charging and storing the batteries.
Therefore:
–
Pos : 39 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku abnehmen + aufsetzen/ACO102, ACO152, AC O/ECO202, AC O202XL, AF P/EFP202 @ 0\mod_1382442983216_18.doc x @ 1433 @ @ 1
Removing the battery (Fig. 2)
Push in (1) the two release buttons (A) and then remove the battery (2).
Inserting the battery (Fig. 3)
Slide the battery into the device as illustrated until it clicks into place.
Pos : 40 /RVT/Kurz bes chr eibung/Akku allgemei n/Akku Z ustands anzeig e/AC O/ECO202, AC O202XL, AC O/ECO203 @ 0\mod_1382445046754_18.doc x @ 1446 @ @ 1
Battery charge indicator (Fig. 2)
The battery charge is displayed when button (B) is pressed. The number of LEDs lit up denotes the
battery charge. One flashing LED indicates a maximum power reserve of 10%. The battery must be
charged soon.
Charge the batteries before using for the first time.
It is imperative that the operating instructions for the battery charger are complied
with.
15
ACO203 / ECO203
EN