Black and Decker GH1000-B2 Manual De Instrucciones página 23

Always remove the plug from the socket before inspecting a
damaged cable. Be careful not to use your strimmer if the
cable is damaged.
Beware of flying objects.
Keep bystanders away from the cutting area.
Do not expose the appliance to rain or high humidity.
Directive 2000/14/EC guaranteed sound power.
AN IMPORTANT CONSUMER FEATURE
Your tool is DOUBLE INSULATED to give you added
safety. This means that it is constructed throughout
with two separate "layers" of electrical insulation or one
double thickness of insulation between you and the tool's
electrical system.
Note: DOUBLE INSULATION does not take the place of
normal safety precautions when operating this tool. The
insulation system is for added protection against injury
resulting from a possible electrical insulation failure within
the tool.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
ADDITIONAL SAFETY INSTRUCTIONS
FOR GRASS TRIMMERS
Warning! Cutting elements continue to rotate after the
motor is switched off.
f Be familiar with the controls and the proper use
of the appliance.
f Before use, check the power supply cord and
extension cord for signs of damage, ageing and wear.
If a cord becomes damaged during use, disconnect
the cord from the mains supply immediately. Do not
touch the cord before disconnecting the supply.
f Do not use the appliance if the cords are damaged
or worn.
f Wear stout shoes or boots to protect your feet.
f Wear long trousers to protect your legs.
f Before using the appliance, check that your cutting
path is free from sticks, stones, wire and any other
obstacles.
f Only use the appliance in the upright position, with
the cutting line near the ground. Never switch the
appliance on in any other position.
f Move slowly when using the appliance. Be aware that
freshly cut grass is damp and slippery.
f Do not work on steep slopes. Work across the face of
slopes, not up and down.
f Never cross gravel paths or roads while the appliance
is running.
f Never touch the cutting line while the appliance is
running.
f Do not put the appliance down until the cutting line
has come to a complete standstill.
f Use only the appropriate type of cutting line. Never
use metal cutting line or fishing line.
f Be careful not to touch the line trimming blade.
f Take care to keep the mains cable away from the
cutting line. Always be aware of the position of the
cable.
f Keep hands and feet away from the cutting line at all
times, especially when switching on the motor.
f Before using the appliance and after any impact,
check for signs of wear or damage and repair as
necessary.
f Never operate the appliance with damaged guards or
without guards in place.
f Take care against injury from any device fitted for
trimming the filament line length. After extending
new cutter line always return the machine to its normal
operating position before switching on.
f Always ensure that the ventilation slots are kept clear
of debris.
f Do not use the lawn trimmer (edge trimmer), if the
cords are damaged or worn.
f Keep extension cords away from cutting elements.
LINE TRIMMER SAFETY WARNINGS
f Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
f This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Using an Extension Lead
f Cords with rubber insulation: 60245 IEC 53
f Cords with PVC insulation: 60227 IEC 53
ENGLISH • 23