Descargar Imprimir esta página

Black and Decker GH1000-B2 Manual De Instrucciones página 25

Publicidad

Idiomas disponibles

Idiomas disponibles

before further operation is attempted. Do not operate
with a broken hub or spool.
f Damage to cord: Keep power cord away from
rotating line. If you damage the cord, unplug it from
the power supply before moving the tool or examining
the damage. A damage cord must be replaced before
further use.
f Disconnect tool: When not in use, when replacing
line, or prior to cleaning.
f Avoid dangerous environmental conditions: Do
not use electric tools in damp or wet locations. Follow
all instructions in this Instruction Manual for proper
operation of your tool. Don´t use the tool in the rain.
f Do not operate portable electric tools in gaseous
or explosive atmospheres. Motors in these tools
normally spark, and the sparks might ignite fumes.
f Store idle tools indoors: When not in use, tools
should be stored indoors in a dry, locked-up place out
of reach of children.
f Ground fault circuit interrupter (GFCI) protection
should be provided on the circuits or outlets to be
used for the gardening appliance. Receptacles are
available having built in GFCI protection and may be
used for this measure of protection.
f Secure extension cord: Using the cord retainer
shown.
f Stay alert: Watch what you are doing. Use common
sense. Do not operate tool when you are tired.
f Maintain appliances with care: Follow instructions
in maintenance section. Inspect extension cords
periodically and replace if damaged. Keep handles
dry, clean and free from oil and grease.
f Check damaged parts: Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other condition that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by an authorized service center
unless otherwise indicated elsewhere in this manual.
Warning! When servicing double insulated tools,
use only identical replacement parts. Replace or repair
damaged cords.
Warning! To prevent electrical shock hazard, use only
with an extension cord suitable for outdoor use. Always
connect extension cords to a fused line or one protected
by a circuit breaker.
EXTENSION CORDS
Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough
to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss
of power and overheating. The following table shows
the correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the cord.
Minimum gage for cord sets
Volts
Total length of cord in feet
120V
0 - 25
26 - 50
220V
0 - 50
51 - 100
Amperios
More
No more
than
than
0 - 6 A
18
6 - 10 A
18
10 - 12 A
16
12 - 16 A
14
FEATURES (Fig. A)
1. Main Handle
2. On/Off Switch
3. Cord Retainer
4. Auxiliary Handle
5. Safety Guard
6. Cutter Head
ASSEMBLY / REGULATIONS
Warning! The guard must always be installed on the
tool to protect the user.
Never operate the tool without the proper footwear.
Unplug the tool before installing the guard.
1. Place the open center of the guard on the power head
of the line (Fig. A).
2. Slide the guard into the provided slot and tighten the
screws (supplied) into the guard completely, as shown
in Fig. B.
3. The guard is not designed to be removed after
installation.
4. Once installed, remove the cover from the cutting
blade on the guard end.
5. Press the button and move the tube up or down, as
shown in Fig. H, to adjust the length of the tube.
6. Secure the extension cord with the cord retention
device as shown in Fig. C.
OPERATING INSTRUCTIONS
Caution! Always wear eye protection.
Caution! Inspect the area to be trimmed and remove
any wires, cords and other sharp objects that may get
ENGLISH • 25
51 - 100
101 - 150
101 - 200
201 - 300
Wire gauge
16
16
16
14
16
14
12
Not recommended
14
12
12

Publicidad

loading

Este manual también es adecuado para:

Gh1000