Bosch SmartphoneGrip BSP3200 Instrucciones De Servicio Originales página 11

Charging your Smartphone
While the smartphone is in the SmartphoneGrip, it can be
charged at the same time as displaying riding data. If your
smartphone has an inductive charging function, you can
charge the smartphone without needing a cable.
Inductive Charging
The charging process starts automatically when you place a
smartphone with an inductive charging function in the
SmartphoneGrip. The status LED (9) lights up yellow. When
the smartphone is fully charged, the status LED (9) will light
up green permanently.
The charging voltage is switched off when you remove the
smartphone from the SmartphoneGrip.
Charging via USB
If your smartphone does not have an inductive charging
function, you can charge your smartphone via the USB
port (3). To do so, open the USB cap and connect a separate
USB cable (not included in the scope of delivery) to the Mi-
cro-A/B USB port.
Pay attention to the type of plug required for your smart-
phone when purchasing the USB cable.
Note: If the eBike battery reaches a state of charge of
0 %, remove any loads that may be present (e.g. smart-
phone).
Status Indicators
The status LED (9) indicates the following statuses with dif-
ferent colours and lighting patterns.
Status
Charging via USB
Inductive charging starts
Inductive charging
Fully charged
Error message
The following alarm states are detected and will lead to the
inductive charging process being interrupted:
– Detection of foreign objects, e.g. coins, keys and other
metallic objects
– Temperature alarm
If the SmartphoneGrip is outside of the operating temper-
ature range, the status LED (9) will light up red and the
charging process is interrupted. The charging process will
resume as soon as the SmartphoneGrip is back within the
operating temperature range.
– Overvoltage alarm at voltages above 6 V
– Undervoltage alarm at voltages below 4.2 V
Maintenance and servicing
Maintenance and cleaning
Use a soft cloth dampened only with water for cleaning. Do
not use cleaning products of any kind.
Bosch eBike Systems
Behaviour
LED lights up blue.
LED flashes yellow 3 times.
LED lights up yellow.
LED lights up green.
LED flashes red.
Have all repairs performed only by an authorised bike
u
dealer.
Do not clean any of the components with pressurised water.
Transport
If you transport your eBike attached to the outside of
u
your car, e.g. on a bike rack, remove the Smart-
phoneGrip and the eBike battery (exception: built-in
eBike battery) to avoid damaging them.
After-sales service and advice on using products
If you have any questions about the eBike and its compon-
ents, contact an authorised bicycle dealer.
For contact details of authorised bike dealerships, please
visit www.bosch-ebike.com.
Disposal and substances in products
You can find information about substances in products at the
following link:
www.bosch-ebike.com/en/material-compliance.
Do not dispose of eBikes and their components with house-
hold waste.
The drive unit, on-board computer incl. operat-
ing unit, eBike battery, speed sensor, accessor-
ies and packaging should be disposed of in an
environmentally correct manner.
Check that your personal data has been deleted from the
device.
Batteries that can be removed from the power tool without
destruction must be removed before disposal itself and sor-
ted for separate battery collection.
In accordance with Directive 2012/19/EU
and Directive 2006/66/EC respectively, elec-
tronic devices that are no longer usable and de-
fective/drained batteries must be collected
separately and recycled in an environmentally
friendly manner.
Electrical and electronic equipment are collected separately
for pre-sorting by type and helps to ensure that raw materi-
als are treated and recovered properly, thereby protecting
people and the environment.
Please return Bosch eBike components that are no longer
usable free of charge to an authorised bicycle dealer or to a
recycling facility.
Subject to change without notice.
TA -2022/3609
APPROVED
English – 3
0 275 008 3SG | (26.05.2023)