Metabo 601716850 Manual Original página 16

en
ENGLISH
Protect the device from water and moisture.
Do not expose to rain.
WARNING! Unintentional startup can
cause serious injuries. Before
cleaning or maintenance: Switch off
the machine, remove the safety key and remove the
battery packs.
Use battery packs with the same
capacity.
Use battery packs that have the same
amount of charge.
5. Overview
See pages 2 and 3.
1 Cable holder
2 On/off switch
3 Switch bracket
4 Handle (for pushing and steering the machine)
5 Handlebars
6 Grass collection bag
7 Rear ejection flap
8 Mulching key
9 Carry handle
10 Verticutters (for mowing near edges)
11 Lever (central cutting height adjustment)
12 Protective cover (battery packs)
13 Levers of the quick clamps
14 Quick clamps
15 Screws
16 Wing nuts
17 Fill level window
18 Ejection opening
19 Battery pack release button
20 Safety key
21 Battery packs *
22 Capacity and signal indicator *
23 Capacity indicator button *
24 Locking screw for blade
25 Washer
26 Blades
27 Blade holder (the semi-circular holes in the
blade must match the semi-circles of the
machine)
*equipment-specific
6. Initial Operation
6.1 Assemble the handle,
adjusting the handle height
WARNING! Do not damage the cables when
folding and unfolding.
Fig. A: Unfold handlebars (5)
1. Fold handlebars (5) backwards.
2. Fold the levers (13) of the quick clamps (14) .
Note: If the clamping strength is set inappropriately:
Open lever (13). Twist quick clamp (14) . Close
lever (13) again and check clamping strength. If
16
necessary, repeat procedure.
Fig. B: Assemble handle (4) and set handle
height
3. Attach the bar ends of the handle (4), as shown,
onto the handlebars (5).
4. Set the desired handle height by aligning the
handle (4) in one of the three positions (1..2..3..).
5. Insert the screws (15) left and right.
Note: Make sure that the screws (15) (on both
sides) are in the same position (1..2..3..).
Note: Mount the wing nuts (16) on the inside so that
they do not get caught during mowing (e.g. on
branches or hedges).
6. Screw the wing nuts (16) onto the screws (15)
and tighten.
7. Fix the cable in the cable holders (1).
6.2 Preparation for grass collection,
mulching
Collect grass / mount grass collection basket.
Fig. C
1. Unfold the rear ejection flap (7) upwards and
hold.
2. Ejection opening (18) must be empty. If
necessary remove mulching key (8) (lift and put
aside).
3. Hold grass collection basket (6) on its handle
and attach the hook as shown.
4. Close the rear ejection flap (7) .
Mulching / mounting the mulching key. Fig. D
1. Unfold the rear ejection flap (7) upwards and
hold.
2. Remove the grass collection basket (6) .
3. Hold the mulching key (8) on its handles and
insert into the ejection chute. (Push in until the
stop and press downwards. Ensure that the
mulching key has engaged in the designated
recesses .)
4. Close the rear ejection flap (7) .
6.3 Set depth of cut.
Fig. on page 2.
Slightly pull the lever (11) outwards and shift the
guide to the desired position. Let engage in the
desired position.
Adjust the cutting height to the height of the grass to
be cut.
Note: For an optimal mowing result:
Cut off no more than one third of the grass height.
When mowing tall grass, reduce the speed at which
the mower is pushed.
Note: For an optimal mulching result, the lawn
should be mulched regularly. There should be a
maximum of 2 cm of grass cuttings as mulch
(recommendation: position 2 or position 3).
6.4 Battery pack
Fig. E
Charge the battery pack before use.
Recharge the battery pack if performance
diminishes.