Descargar Imprimir esta página

Mitsubishi Electric Fresh Master GUF-50RDH4 Instrucciones De Funcionamiento página 8

Ocultar thumbs Ver también para Fresh Master GUF-50RDH4:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 58
3. How to operate
3.1. When interlocked with an indoor unit
- Operation will be synchronized with an indoor unit.
- The humidifier will be operated by the heating signal received from
the indoor unit. (For GUF-50, 100RDH4)
- In the case of GUF-50, 100RDH4, there is no temperature control
since the temperature is adjusted according to the outside air
temperature.
Starting and stopping operation
- Using the Remote controller to start or stop the indoor unit will
automatically start or stop the Fresh Master.
Operation modes
- The Fresh Master will operate in the same mode as the synchro-
nized indoor unit (heat, cool and fan).
- The Fresh Master will be cool when the indoor unit is operated in
dry mode.
When using with multiple indoor units
- When using with multiple indoor units that are set differently, the Fresh
Master will operate in the mode with priority of: heat, cool and fan.
When operating only the Fresh Master
- The Fresh Master can be operated independently by pressing
the Ventilation button on the Remote controller (in this case, the
operation mode will be fan).
- Pressing the Ventilation button each time will switch the display
between Stop, Low and High.
Stop
3.2. When not interlocked with an in-
door unit
- GUF-50, 100RD4 will adjust the temperature according to the
indoor temperature set using the Remote controller.
- In the case of GUF-50, 100RDH4, there is no temperature control
since the temperature is adjusted according to the outside air
temperature.
3.2.1. Before starting operation
- Make sure that the power supply is turned ON before use.
(Keep the power supply turned ON at all times when the Fresh Master is
in use. Use of the unit without power can result in compressor failure.)
- Start running after the "HO" display has disappeared. The "HO"
display briefly appears on the room temperature display (max. 10
minutes) when the power is turned on and after a power failure.
This does not indicate any failure of the Fresh Master.
- The operation modes of the Fresh Master air-cooling operation
and heating operation are different from those of the outdoor units.
When the operation is started with cooling/heating and other
indoor units or the Fresh Master connected to the counterpart
outdoor units are already running in the same operation mode, the
Remote controller displays air-cooling/heating mode. However,
the operation comes to stop, and you cannot get a desired mode.
When this occurs, you will be notified by the "cool" or "heating"
display that flashes in the liquid crystal display of the Remote con-
troller. Set to the operation mode of other indoor unit or the Fresh
Master by the operation switch button.
The above does not apply to the models that simultaneously run
both the cooling operation and heating operation.
- The outdoor units stop when all the indoor units and the Fresh
Master connected to the counterpart outdoor units stop.
- During heating operation, even if the indoor unit or the Fresh
Master is set to operation while the outdoor unit is in defrosting
operation, operation starts after the defrosting operation of the
outdoor unit has ended.
Low
High
Warning:
- Check and confirm the power circuit before use. For con-
tents, refer to the previously described chapter [Crucial
points to be observed for safety].
3.2.2 ON/OFF
Operation lamp
Start an operation
Press [ON/OFF] button
Operation lamp lights up and operation starts.
Stop an operation
Press the [ON/OFF] button again
Operation lamp goes off and operation stops.
- Once the buttons have been set, pressing of the [ON/OFF] button
only can repeat the same operation thereafter.
- During operation, the operation lamp above the [ON/OFF] button
lights up.
Caution:
- Even if the operation button is pressed immediately after the
operation has stopped, operation will not restart for about 3
minutes. This function protects the machine. It automatically
starts operation after approximately 3 minutes.
3.2.3. Selecting operation
Operation mode
[selecting operation]
button
When selecting operation
Press the [selecting operation] button
- Consecutive press of the selecting operation button switches the
operation over to "cooling," "fan," "(automatic)," and "heating." For
the contents of operation, check the display.
For cooling
Press the [selecting operation] button and bring up the "cool-
ing" display
[ON/OFF] button
7

Publicidad

loading