Victron energy BLUE POWER Multi RS Solar Manual página 60

Figura 6. Diagrama completo de cableado de Multi RS Solar
IMPORTANT INFORMATION ! IMPORTANT INFORMATION !
Solar array configuration setup info-1 Solar array configuration setup info-2
The Multi RS Solar Dual Tracker contains multiple When the RS MPPT switches to float stage it reduces the battery charge current by
PV input connectors. These are wired to two increasing the PV Power Point voltage. The maximum open circuit voltage of the PV
individual Maximum Power Point Trackers. array must be less than 8 times the minimum battery voltage when at float.
It is possible to use different panel configurations For example, where a battery has a float voltage of 54.0 volts as with the batteries
within the specifications for each PV input used in this drawing, the maximum open circuit voltage of the connected array cannot
connector. You should NOT connect the same PV exceed 432 volts. Where the array voltage exceeds this parameter the system will give
array to both tracker inputs.The max operational a "Over-charge Protection" error and shuts down. To correct this, simply reduce the
input current per PV input is 13A. PV voltage by removing a panel from the Array string.
The smallBMS is enlarged visible
smallBMS POWER +
Bat +
LOAD DISCONNECT
Load
Pre-alarm PRE-ALARM +
Load ON
These BMS M8 circular connectors are enlarged visible Charger CHARGE DISCONNECT
Temp or OVP
Bat -
POWER -
Remote L
victron energy ON/OFF SWITCH
Remote H
BLUE POWER ON/OFF SWITCH
All BMS M8 Circular connectors are
daisy chained connected to the BMS !
4 x Lithium 25.6V-200Ah
Smart LiFePO4
victron energy
BLUE POWER
Lithium
25.6V-200Ah
Smart LiFePO4
victron energy
BLUE POWER
Lithium
25.6V-200Ah
Smart LiFePO4
KEEP NEGATIVE BATTERY CABLES ALL AS SHORT KEEP POSITIVE BATTERY CABLES ALL AS SHORT
AS POSSIBLE AND ALL AT THE SAME LENGTH ! AS POSSIBLE AND ALL AT THE SAME LENGTH !
IMPORTANT INFORMATION ! IMPORTANT INFORMATION ! IMPORTANT INFORMATION !
Recommended AC Out-1 cable/breaker size Multi RS Recommended AC Out-2 cable/breaker size Multi RS Recommended DC cable/fuse size Multi RS Solar
With Power assist the Multi RS can add 6kVA AC Out-2 only is available when power is 0-2 m cable length: 35SQmm, 2-5 m cable length:
or 26A to AC Out-1 for peak handling when present on AC IN and AC Out-2 supports up 70SQmm. When used in closed conduits, cable
needed. The Multi RS can throughput 50A from to 50A similar to the maximum connected size should double. Cable length stands for the
the AC input directly to the output loads. AC IN power source as they are internally distance between the batteries and the Multi RS
The AC input relays are limited to 50A max. connected. An Earth leakage device with a connections !!! Recommendations are without
An Earth leakage device with a breaker size of breaker size of 50A max or less or a other loads in the system and these also should be
50A max or less or a combination MCB/RCD combination MCB/RCD must be installed taken into account for proper main battery, main
must be installed on the output of AC Out-1. on the output of AC Out-2. Cable size fuse & main switch cables !!!
Cable size should be adjusted accordingly. should be adjusted accordingly. Fuse size should be 125-150A.
Puede consultar aquí los diagramas de mayor resolución y más actualizados
chargers/multi-rs-solar#system-schematic
Página 57
Multi RS Solar
GX TOUCH 50
GX TOUCH 50
AC Input Inverting AC Loads
IMPORTANT INFORMATION !
0W victron energy 425W
Solar array configuration setup info-3
The Multi RS Solar has a built in AC PV inverter detection system. When feedback is
detected of AC PV power on the AC-output side, frequency shift will automatically be
enabled. While no further configuration is required, it is important that the AC PV inverter
PV-Charger
is configured correctly to respond to a rising frequency adjustment by reducing its - 75% + victron energy
output. Be aware of the 1:1 rule of any AC PV inverter size to the Multi RS size, and 1250W
minimum battery sizing applies. More information about these limitations are available in
DC Power
870W
the Victron AC Coupling manual, and this document is required reading if using any AC 51.2V 17A -....W
PV inverter. More info is available in the Multi RS manual and on the website.
victron energy
VE.Can to/from Multi RS
From terminal fuse
MPPT remote-H/6
Multi RS remote-H/6
Multi RS Solar 48/6000 Dual Tracker
MPPT remote-L/5
Multi RS remote-L/5
From central negative
60 Volt/16mA
PRE-ALARM BUZZER
BMS On/Off Switch
IMPORTANT INFORMATION !
Victron LiFePO4 Smart batteries
When using Victron lithium batteries, the system will need to be
wired using the allow to charge ATC, and allow to discharge ATD
contacts from the Victron smallBMS to the I/O connection port of
both RS devices. This will also need to be configured to BMS
mode when commissioning the product with VictronConnect.
BJE-303B
Li-DISTRIBUTION
MAIN SWITCH
ON
HOUSE
Single Circuit
FUSE FUSE
To/From Cerbo
VE.Can to/from Cerbo
from smallBMS
Multi RS remote-H
Multi RS remote-L WARNING !
High Voltage DC
Multi RS Solar enlarged
I/O & Data connections
smallBMS-
CERBO-
NEGATIVE BUSBAR
VE.Direct
VE.Can TERMINATOR VE.Can
To/From Cerbo
VE.CAN to/from Cerbo VE.Can
IMPORTANT INFORMATION !
Recommended AC IN
cable/breaker size Multi RS Solar
AC IN must be protected by a circuit
breaker rated at 50A max or less. This
depends heavily on the size of the
connected power source.The input current
must be adjusted to fit the size of the
connected power source.
User I/O
The breaker and cable size for AC IN From SmallBMS
should be adjusted accordingly.
ATC or CHARGE DISCONNECT-L/5
ATD or LOAD DISCONNECT-H/6
Bottom left hand side
CERBO GX
Multi RS Solar Arrays
VE.Can to/from MPPT RS
VE.Can to/from Multi RS
ETHERNET
HDMI
VRM
WORLD
CERBO Power -
CERBO Power +
MPPT RS remote-H/6
MPPT RS remote-L/5
VE.Can to/from MPPT RS
MPPT RS remote-H/6
MPPT RS remote-L/5
AC Power from Grid
GRID Power
WARNING !
230V Volt AC
AC Power from: AC Power from:
Output-1 Output-2
1 N 1 N
name
name :hager :hager :hager name :hager :hager :hager name
ADxxxxx xxA/I n0.03A ADxxxxx xxA/I n0.03A
T T 0 OFF 0 OFF 0 OFF
Bx test regularly Bx test regularly
0 0
0 OFF 0 OFF 0 OFF 0 OFF 0 OFF 0 OFF 0 OFF 0 OFF
MCB MCB
earth fault indicator earth fault indicator
MCB/RCD MCB/RCD MCB
PV1
2 N 2 N
power
Multi RS Multi RS
AC Out-1 AC Out-2 AC in
Switched load-3
Switched load-2
Switched load-1
No Break load-3
WARNING ! No Break load-2
230V Volt AC
No Break load-1
Multi RS AC IN
Multi RS AC OUT-2
Multi RS AC OUT-1
PV-1 Power +
PV-1 Power -
PV-2 Power +
PV-2 Power -
IMPORTANT INFORMATION ! IMPORTANT INFORMATION ! IMPORTANT INFORMATION !
When operating in inverter mode, the Neutral output of a In a fixed installation like in this drawing, an uninterruptible grounding Be aware that local rules
inverter/charger must be connected to ground to guarantee can be secured with the grounding wire of the AC input. It will however may require alternative
proper functioning of a GFCI or RCD device. In case of a be good practice to ground the casing to the AC ground Busbar in the AC ground configurations !
split phase supply the Neutral also must be grounded. AC Distribution panel as well as is visible in this drawing.
User I/O User I/O functions Multi RS and MPPT RS
I/O Number Connection Description
1 Relay_NO Programmable relay Normally Open connection
2 AUX_IN- Common negative for programmable auxiliary inputs
3 AUX_IN1+ Programmable auxiliary input 1 positive connection
4 AUX_IN2+ Programmable auxiliary input 2 positive connection
5 REMOTE_L Remote On/Off connector Low or ATC connection with SmallBMS
6 REMOTE_H Remote On/Off connector High or ATD connection with SmallBMS
7 RELAY_NC Programmable relay Normally Closed connection
8 RELAY_COM Programmable relay Common negative
9 TSENSE- Temperature Sensor negative
10 TSENSE+ Temperature Sensor Positive VE.Can TERMINATOR
11 VSENSE- Voltage Sensor negative
12 VSENSE+ Voltage Sensor Positive
To/From Cerbo
VE.CAN to/from Cerbo
From SmallBMS
ATC or CHARGE DISCONNECT-L/5
location: ATD or LOAD DISCONNECT-H/6
https://www.victronenergy.com.es/inverters-
Optional MPPT RS Solar Array
Optional SmartSolar MPPT RS
name name
PV
BREAKER
0 OFF 0 OFF 0 OFF
ISOLATOR
MCB
PV2 PV
power power
To/From Cerbo
VE.Can to/from Cerbo
FROM PV
from smallBMS
MPPT RS remote-H
BREAKER/ISOLATOR
MPPT RS remote-L WARNING !
High Voltage DC
MPPT RS Solar enlarged
I/O & Data connections
VE.Direct
VE.Can
VE.Can
User I/O
location:
Bottom left hand side
Apéndice