GRAPHITE 59G086 Instrucciones De Uso página 11

GWARANCJA I SERWIS
Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service tel. +48 22 573 03 85
Ul. Pograniczna 2/4 fax. +48 22 573 03 83
02-285 Warszawa e-mail graphite@gtxservice.pl
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna
gtxservice.pl
GRAPHITE zapewnia dostępność części zamiennych oraz materiałów
eksploatacyjnych dla urządzeń i elektronarzędzi. Pełna oferta części
i usług na gtxservice.pl.
Zeskanuj QR kod i wejdź na gtxservice.pl
do napraw gwarancyjnych
na platformie internetowej
TRANSLATION OF THE ORIGINAL
INSTRUCTIONS
ANGLE GRINDER
59G086
NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME, READ
THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
ANGLE GRINDER, SAFETY WARNINGS
Safety guidelines for grinding, sanding with sandpaper, working
with wire brushes and cutting using the grinding wheel.
• This power tool can be used as a regular grinder, sander
for sanding with sandpaper, grinder for grinding with wire
brushes and for cutting with a cut-off wheel. Observe all safety
guidelines, instructions, descriptions and data provided with
the power tool. Failure to observe the following recommendations
may cause danger of electric shock, fire and/or serious injuries.
• This power tool cannot be used for polishing. When the power
tool is used for other works than it is designed for, it may contribute
to hazards and injuries.
• Do not use equipment, which is not designed and
recommended by the manufacturer specifically for this
device. The fact that it can be fastened to the power tool, does not
guarantee safe operation.
• The permissible rotational speed of a working tool used
cannot be lower than the maximum rotational speed given on
the power tool. A working tool rotating faster than the permissible
speed may break and its parts may chip off.
• The outside diameter and thickness of a working tool must
correspond to dimensions of the power tool. A working tool of
incorrect dimensions may not provide sufficient control and covering
of the power tool.
• Working tools with threaded inserts must perfectly fit the
thread in the spindle. In case of working tools that are
fastened using a flange, the hole diameter of a working tool
must fit the flange diameter. Working tools, which cannot be
precisely seated in the power tool, rotate unevenly, vibrate heavily
and may result in loss of control over the power tool.
• Under no circumstances, should damaged working tools be
used. Before the power tool is used, accessories such as cut-
off wheels should be checked for chips and cracks, grinding
wheels should be checked for cracks, abrasion or heavy
wear, while wire brushes for loose or broken wires. When the
power tool or a working tool is dropped, it must be checked
for damage or another, undamaged tool should be used. If a
working tool is checked and fastened, the power tool should
be switched on for a minute at the highest speed, paying
attention so that the operator and bystanders are beyond the
zone of the rotating tool. Damaged working tools often break in
this test period.
• Always wear personal protective equipment. Depending on a
type of work, a full face mask, eye protection or safety glasses
should be worn. A dust mask, ear protection, protective
gloves or a special apron protecting against small particles of
abrasive material and workpiece should be worn, if needed.
Protect your eyes against airborne foreign bodies occurring during
operation. A dust mask and protective mask for the respiratory
system must filter dust occurring during work. The influence of noise
for a longer period of time may lead to deterioration of the hearing.
• Always make sure bystanders are in a safe distance from
the power tool reach zone. All people staying in the vicinity
of the operating power tool must use personal protective
equipment. Chips of a workpiece or broken working tools may chip
off and cause injuries also beyond the direct reach zone.
• When works are performed, during which the power tool may
encounter hidden electric conductors or own power cord,
the power tool should be held by the isolated surfaces of
11